I have two Unifi plans for two properties:
House A <--- 300mbps
House B <--- 100mbps
Can I just swap the Unifi plan by swapping the PPoE user id?
Official TM UniFi High Speed Broadband Thread V39, READ 1ST PAGE FOR RELEVANT WIFI INFO
|
|
 May 17 2021, 07:11 PM
Return to original view | Post
#1
|
 
Junior Member
37 posts Joined: Apr 2011 
|
|
Quote|
|
|
|
|
May 18 2021, 03:57 PM
Return to original view | Post
#2
|
|
Junior Member
37 posts Joined: Apr 2011
|
QUOTE(newlich @ May 17 2021, 07:11 PM) I have two Unifi plans for two properties: Well, it doesn't work.House A <--- 300mbps House B <--- 100mbps Can I just swap the Unifi plan by swapping the PPoE user id?  What happen is: House A <--- 100mbps (normal) House B <--- 85mbps (capped, instead of 300mbps) Is there any configuration changes needed to be done for my modem/router? |
|
|
May 18 2021, 08:47 PM
Return to original view | Post
#3
|
|
Junior Member
37 posts Joined: Apr 2011
|
QUOTE(aniq8676 @ May 18 2021, 06:17 PM) have you tried this way, YOU ARE FCKIN GENIUS. I'm going to try this method. BTW, is the BTU thing being configured in modem?Both modem and router in house (A) bring it to house (B), while the modem and router in house (B) bring it to house (A). |
|
|
May 18 2021, 08:52 PM
Return to original view | Post
#4
|
|
Junior Member
37 posts Joined: Apr 2011
|
QUOTE(newlich @ May 18 2021, 08:47 PM) YOU ARE FCKIN GENIUS. I'm going to try this method. BTW, is the BTU thing being configured in modem? OK. I just googled. I guess the BTU you meant is the Huawei HG8240H Modem. |
|
|
May 20 2021, 01:21 PM
Return to original view | IPv6 | Post
#5
|
|
Junior Member
37 posts Joined: Apr 2011
|
QUOTE(newlich @ May 18 2021, 03:57 PM) Well, it doesn't work. Here is some updates. After some studies, I realized that I couldn't just swap the BTU due to the ONU password is different for different area. Initially, I wanted to access the BTU to get the ONU password and swap them, but I can only access HG8240H5. I couldn't access HG8240H (even though I can ping 192.168.100.1, but the website doesn't load). So I have gave up this project. When I accessed HG8240H5, I realized there were nothing about internet speed in the configuration. I don't think it will works even I swap the BTU together with correct ONU password. The internet speed configuration probably is in port or somewhere else.What happen is: House A <--- 100mbps (normal) House B <--- 85mbps (capped, instead of 300mbps) Is there any configuration changes needed to be done for my modem/router? |
|
|
May 24 2021, 04:20 PM
Return to original view | IPv6 | Post
#6
|
|
Junior Member
37 posts Joined: Apr 2011
|
QUOTE(aniq8676 @ May 20 2021, 01:58 PM) May i know, do House A and House B use the same FDC code? An example is BS C016 . If both houses use the same fiber cabinet, it is not a problem to make a swap Yup. I swapped and it doesn't works.  FYI, both houses are 16 km apart.QUOTE(PRSXFENG @ May 20 2021, 02:12 PM) You need to unplug the fibre cable before powering it on to access it ircc, as it receives configs from the OLT to disable the web page, and also that's where the speed config is set ircc. Yup. I unplugged the fiber cable before access it. No luck EDIT: this might be wrong, try 1.254 or 100.254 Also, do not use the root/adminHW password printed on the modem, use telecomadmin/admintelecom, this shows more options. Do not look at the fibre btw, it's laser and it can blind you. I think @Anime4000 knows better (sorry I don't know how to mention someone on lowyat forums)  |
|
|
May 24 2021, 04:51 PM
Return to original view | IPv6 | Post
#7
|
|
Junior Member
37 posts Joined: Apr 2011
|
Guys, should I enable IPv6 for Unifi? I mean, will it be better in term of speed and stability?
|
|
Topic ClosedOptions
|
| Change to: |  0.1958sec
 0.68
 7 queries
 GZIP Disabled
Time is now: 14th December 2025 - 01:35 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.