Welcome Guest ( Log In | Register )

Outline · [ Standard ] · Linear+

 XiaoMi AX3600 AX1800 AX5 Vlan tagging

views
     
jchong
post Jan 23 2021, 04:20 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
QUOTE(heidarren @ Dec 5 2020, 06:46 PM)
Check via SSH command, China AX3600 has 31dBm/29dBm/27dBm for txpower high/mid/low, int firmware might have much lower txpower in order to match worldwide regulations.
*
Say, any idea what is txpower for Xiaomi AX1800?
jchong
post Jan 23 2021, 04:34 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
Another question, how to connect my AX1800 to the Mi Wi-Fi app on my phone?

After launching the app, I come to this screen and tap "+Add Mi Router"
Attached Image

Then the app shows searching...
Attached Image

Then it jumps to this screen...
Attached Image

Basically I'm stuck here. The app can't seem to find any devices to connect to.
jchong
post Jan 23 2021, 08:27 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
QUOTE(heidarren @ Jan 23 2021, 06:26 PM)
Change app region to mainland China
*
Thanks. It worked.
jchong
post Jan 25 2021, 03:46 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
Got another question on the AX1800, in the app I'm using English language. But then I saw one new option (under Wifi settings) which is written in Chinese:

Attached Image

Any idea what this is about? Should I leave it on or off?
jchong
post Jan 25 2021, 11:09 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
QUOTE(go626201 @ Jan 25 2021, 10:49 PM)
This is enabled for automatic pair New Mi-Home hardware that haven't connect to the network.
*
Thanks
jchong
post Nov 18 2021, 03:39 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
I've been using the Xiaomi AX1800 router with Unifi for the past 10 months. But yesterday it would not connect - the Internet light is orange. I rebooted the router also the same.

I put back in my old D-Link 850L router and it managed to connect to Unifi. Any idea what could be wrong?

Or maybe did Unifi change something and I need to update the settings inside the AX1800 to connect?
jchong
post Nov 18 2021, 06:18 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
QUOTE(toytoy @ Nov 18 2021, 05:57 PM)
The last time it happened to my AX3600 I also got panicked and spent 2 hours troubleshooting but end up checking lowyat forum and there was an outage from Unifi...
Did u plug it back since? are the configs still intact? maybe restore factory setting? backup ur config though.
*
I did plug in the AX1800 again today morning and still cannot connect. The configs are intact. When I swap back to the old D-Link no problem.

Yeah, maybe I'll do a factory reset and see how it goes.
jchong
post Nov 19 2021, 04:47 PM

****************
*******
Senior Member
5,989 posts

Joined: Nov 2005
Say, is there a way to set VLAN inside the AX1800?

 

Change to:
| Lo-Fi Version
0.0200sec    0.52    7 queries    GZIP Disabled
Time is now: 16th December 2025 - 10:27 PM