Outline ·
[ Standard ] ·
Linear+
Tp-Link AX50 Dect Phone Connection, Maxis Home Fiber
|
TSspamfish
|
 Jul 12 2020, 05:09 PM, updated 6y ago
|
Getting Started
|
Hi sifus,
need some help here. I just bought the Tplink Ax50 router to replace the white Maxis provided router (Aminia AC1200). Using the Tplink web access I configure it to use the maxis profile enabling IPTV to Lan port 1 and VoIP to Lan port 4. Then I hooked the DECT phone RJ11 directly to Lan Port 4 on the Ax50. However I cant seem to get the phone line to work. Is there anything that I missed out or mistake done?
Thank you for the opinion in advance.
|
|
|
|
|
|
TSspamfish
|
Jul 12 2020, 05:24 PM
|
Getting Started
|
Another alternative thought process is if the above cannot be done, I was thinking of connecting the DECT phone back to the Alcatel-Lucent ONU that is provided by TM.
However, I dont know if the ONU can be configured to point to the maxis server instead.
|
|
|
|
|
|
TSspamfish
|
Jul 12 2020, 10:11 PM
|
Getting Started
|
QUOTE(YoungMan @ Jul 12 2020, 08:40 PM) I think you need to connect the maxis router to port 1 and connect the phone to maxis router. There is no RJ11 port for voip on your current router so the Maxis router is use to bridge voip. You mean use back the original maxis router and use the AX50 as a AP instead? Btw you can plug in RJ11 into RJ45 port |
|
|
|
|
|
TSspamfish
|
Jul 13 2020, 09:42 PM
|
Getting Started
|
QUOTE(delaciox @ Jul 13 2020, 06:11 PM) it you ax50 is main router , LAN 4 for voip, than your router ac1200 wan port must connect to ax50 lan port 4, and phone still connect ac1200 you cannot just rj11 into rj45 port I dont want to connect AX50 -> Aminia AC1200 -> Alcatel ONU I want AX50 -> Alcatel ONU RJ11 can plusg into RJ45 socket. The only thing is that the Pin assignment need to match correctly. In this case I do not know the pin assignment for the DECT phone vs the router Lan port 4 |
|
|
|
|
|
TSspamfish
|
Jul 14 2020, 01:12 AM
|
Getting Started
|
QUOTE(delaciox @ Jul 13 2020, 10:38 PM) Alcatel ONT lan port 2 -> AX50 lan port4-> aminia ac1200 wan port. next time you better change got rj11 router it you want use the phone. most people change router is no more use wire phone. RJ45 ≠ RJ11 rj45 for network signal rj11 for phone signal oh you mean using the aminia as the secondary router dedicated only for the DECT...good idea. thank you for the insight. Just to confirm. Alcatel ONT lan port 2 -> AX50 WAN port. AX50 Lan Port 4 to Aminia AC1200 WAN port. |
|
|
|
|
|
TSspamfish
|
Jul 28 2020, 08:50 PM
|
Getting Started
|
QUOTE(mroctopus @ Jul 26 2020, 12:23 PM) hi andrekua, i did exactly the same as instruction written. AX50 port 4 (VOIP) connect to Maxis Router (Wan port) and RJ11 connected at Maxis router. It give me engaging tone and cant dial through. "(optional) Should want to use the VoIP service provided, tagging traffic on a LAN port (of your choosing) and the WAN port on your router with vlan id 821, 822. This allows the VoIP traffic to pass between LAN port and the WAN port, and no where else. I used the Maxis issued Technicolor TG784nv3 router to handle the VoIP connection. The Maxis router’s WAN is plugged into the designated LAN that you have chosen. No additional configuration is needed in the part of the Maxis issued router, the modem as configured by the service technician will work fine." Yep I am getting the same issue. Will try to call maxis and see if there is a solution to this. |
|
|
|
|
Quote
0.0174sec
0.51
6 queries
GZIP Disabled