Here comes BLITZ FORMULA A mobo that is full of bling bling( u can find lots of LED on this mobo and the LED is very bright---disturbed my sleep.



The IO Panel. There is Clear CMOS Button at the IO Panel. So u can easily Clear yr CMOS without opening yr side panel(Casing). A plus for me so that I do not need to clear the jumper for CMOS on the mobo. But, Asus has a good 'recovery' after faile din OC so, I did not touch the CMOS jumper at all for the whole process of testing and oc.



Command Rate for Memory: 1T or 2T at yr disposal. Of course, it depends on yr memory if it can take the command rate.



Max vcore for CPU is 1.90vcore. For extreme overclocker. This is not enough. But for me, it is more than enough.


Loadline Calibrtion. Is this like CPU voltage Dumper???Anyway, I will always leave it as ENABLE for OC. Still need to investigate further what is this option does.


Max vdimm for memory is 3.40vdimm.This is good for my DDR2 BH5-OCZ Reaper HRC PC9200.



DDR2 Ref Voltage. hm....not idea what this options does. Need to investigate further. But initial testing showed that this does not effect the oc of the memory. I will leave it as AUTO.



South Bridge Voltage: Max is 1.225volt. I wil leave as AUTO for OC.



PLL Voltage. Max is 2.0volt. Save u the hussle to hardmod it. This option has great impact on yr CPU FSB. In order to break teh so-called FSB wall, u need more voltgae from this PLL.

---

Added on July 26, 2007, 1:32 pmWill post more later

This post has been edited by Newsman: Jul 26 2007, 01:32 PM

Im a tester from singapore

---

Added on July 26, 2007, 1:46 pmHow can i post more?

It keeps adding to the first post and it says tht im posting too many pictures

This post has been edited by Newsman: Jul 26 2007, 01:46 PM

Memory Overclocking

Memory: OCZ Reaper Series. HPC Edition. PC 9200 1gb x 2 kit

600mhz @ 4-4-4-12@2.78vdimm with Pi 32mil, sandra and 3D Mark 03. My OCZ really loves high vdimm PC Probe II tends to report more volt. Maybe the reading is a bit off or the reading is accurate. Anyway this does not concern me.



610mhz@4-4-4-12@2.82vdimm with pi 8 million and sandra.


640mhz@5-5-5-15@2.60vdimm with Pi4 million and sandra


656mhz@5-6-5-15@2.64vdimm with pi 4miilion and sandra


670mhz@5-6-5-15@2.66vdimm with pi 4million


680mhz@5-6-6-15@2.78vdimm with Pi 1 million


691mhz@5-6-6-18@2.86vdimm...9mhz more to 700! more juice more juice!!




This post has been edited by Newsman: Jul 26 2007, 02:42 PM

Things to take note about the low temp on G0 stepping

My E6550 reach around 63 degree c at full load at 3.5ghz @ 1.45vcore on Asus Blitz Formula as compared to Asus P5K-E and Asus P5KC....

Wonder the sensor screwed on the mobo or something else. But what I can tell you is that the heatsink is HOT when I touched it so it is tally with the reading at about 63 degree during full load on Asus Probe II. On core temp and TAT. Full load only 50 degree clecius.

So, the mobo itself in effecting the load temp??

If u have this mobo pls confirm the reading of the load temp of yr G0 stepping CPU.

*reserve for updates*

---

Added on July 26, 2007, 2:45 pm*reserve for updates*

This post has been edited by Newsman: Jul 26 2007, 02:45 PM

*reserve for updates*

u will never regrret buying the reapers unless ur using ddr3 ofcos

board cant SLi until someone cracks it