what is push + pull config? =.="

errr... sry for asking noob question, but wats VTT?? and oso, y la even though i put 1.65 for vcore, my proc is still not stable although its just 4ghz =.="

my vdimm is 2.3... vnb i put auto, vfsb oso auto... sry but im still a noob in oc'ing wwwww

my fsb termination voltage has a range of 1.20 to 1.50 volts... so is it ok for me to just put it to the max? or is the a fine balance?

my vid is 1.3, im using the g0 stepping... 3.6ghz @ 1.4v stable but failed prime95 stress test @@... for 4ghz, i put 1.69 oso not stable at all T_T

the cpu voltage ref n nb voltage ref got few values like 0.67x, 0.63x, 0.57x n so on... what do those values mean ehh???

i see.... sry for being noob >"<... but why i still cant push to 4ghz? T_T... izzit bcos my temp too high??? since im using stock hsf idle @ 4ghz in bios info is 70c @@

i did stress test my cpu... so far the most stable settings for me is 3.2ghz @ 400fsb x8 @ 1.28v... any higher it will not be stable anymore T_T

hmmm at 1.45v cpu still not stable @ 3.6ghz... after 3-4 minutes on prime95, get bluescreen n restart... on stock hsf, 3.6 @1.45v core temp is around 60c, and cpu temp is 50+ idle @@

i see... hopefully when i get my new heatsink can get stable oc @@

hmmm... my gtl ref for cpu oni got 0.63x, 0.61x but no 0.67x @@ so which should i choose? but my nb gtlref got 0.67x @@

my ram ddr2-800 oc to 961mhz, if 1.9 surely keep crashing... i no choice but to put at 2.3 for stability >"<

i wanna ask, anyone reached 4.5ghz b4??? for those who've reached it, can u tell me wats ur vcore???

mind sharing me ya settings if u succeed?

---

Added on November 14, 2008, 9:13 pmsame as me T_T.. 4ghz can boot to windows... but try do prime95 test, blue screen after 30 seconds =.="... vcore at that speed 1.616... so high can kill my proc @@...

This post has been edited by iBenQ: Nov 14 2008, 09:13 PM

1.625 @@... dun dare go dat high, i get over voltage warning, 1.616 is the highest can go without warning ...

mine @ 3.8ghz i just use 1.55 vcore can pass performance test, but havent tried prime95 yet >"<... 3.6ghz @ 1.45v full load temp less than 70c for each core and defnitely stable cos pass prime95 test for few hours

HOW HOW!!!.. interested here ahahaha... but can someone tell me wat factors cause bluescreen when benchmarking my proc @ 4ghz??? izzit temp too high or voltage too low? >"<

no longer using stock hsf ... me using cm z600 with 2 fans for push n pull config... temp @ 1.616v load not sure but idle is around 45~49c core temp, ok oso ma this temp >"<... but keep blue screen when trying to benchmark T_T...

so i think for cooling system i got it ok, but jz oc settings T_T

@ 4ghz my ram is 890mhz, so i put to just 2.00vdimm, as for gtl ref, my cpu gtl ref tweak only got 0.63,0.61,0.57,0.51 T_T... but for nb gtl ref got 0.67 and 0.61... so which gtl ref shud i use? @@

as for vcore, i set in bios 1.65v but vdroop make it 1.616v... any higher i will get cpu over voltage error warning, so i dun dare go higher T_T

wohh... nice vcore... mine @ 3.6ghz is 1.445v.. but judging from ur temp, u using stock hsf??

hmmm.. temp a lil high for me... 1.345 vcore shud not get 70c on stress test IMO... shud be 60+ since u not using stock hsf... mine 1.45v stress test core temp stucked at 70c too...

linx n ibt are stress tests to c if ur system is stable at ur oc settings just like prime test, but temps go higher >"<

but with dat temp u can still use it 24/7, just like wat im doing now... wat more ur vcore lower than mine by 0.1++ @@... how u tweak T_T

This post has been edited by iBenQ: Nov 23 2008, 05:14 AM

if i have xtra proc lying around, or im rich enough to buy another proc, y not?
btw, how u lap?? self lap or go shop do? @@

wat u do till full load for 8 months @@

at last my heatsink jz came back from RMA @@

tried lots of things when my heatsink is gone

my water cooling kit from japan



downgrade back to air cooling



cut my finger when trying to move the cm 90cfm fan while its still turned on T_T



This post has been edited by iBenQ: Nov 30 2008, 07:39 AM