guys , need some opinion.

i'm using P35-DS3P motherboard , E6400 CPU , 2GB XMS2 DHX Corsair 800MHz C4 ram, zalman 9700LED cooler, FSP 600 watts true power.

i'm currently running at 3.2GHZ without problems, however if i wish to go beyong 3.2GHz exp. 3.4GHZ , 3.5GHz i encounter problems during start up blue screen , auto restart etc ..... but you guys here managed to go beyong 3.5GHZ

Using Windows Vista Ultimate 64-bit
400MHZ X 8 multiplier = 3.2GHZ
my VCORe voltage is : 1.408V
RAM voltage : 2.2v
ram timing : 5-5-5-15
memory ratio 4:5
now RAM running at 1000MHZ
PCI-Express at 100Mhz

now i using system voltage control to AUTO .

advise plsplsps i wan to reach 3.6GHz plsplspspls I abit confuse on increasing voltages here plspsls advise

another question my RAM is meant to be run at timing 4-4-4-12 but the CPU-Z detected 4-4-4-13 is it normal or my ram is faulty ??



advice greatly appreciated

ya from HP XD

---

Added on October 19, 2007, 12:19 amdude i tried your suggestion and i increase the FSB to 425 X 8 = 3.4GHZ TAK JADI ... lol loading microsoft then BLUE SCREEN mentioning DUMPING PHYSICAL MEMORY then auto restart... lol any more thoughts??

AND can i set my RAM run above 1000MHZ exp . 1100MHZ++ by setting timing lower then 5-5-5-15 ? prefer Cas 4 lol~~ you may suggest any available timings for my RAM . TY

This post has been edited by Ezonizs: Oct 19 2007, 12:51 AM

kk i'll try lol nvm suicide run then january change Q9450 XD woot..... if i need to chnage to liquid cooling system but DAMMIT i'm using cooler master centurion 5 casing ...... cannot put the pump and Reservoir casing too PACK and my graphic card is 8800GTX used up two slots and plus a soundcard unless i opt for external liquid cooling which is much more expensive T.T

This post has been edited by Ezonizs: Oct 19 2007, 11:43 AM

guys, i ocied my E6400 to 3.4Ghz using 1.52V issit safe ? i'm on Zalman 9700LED CPu cooler~~~ i can't reach 3.6Ghz with 450 X 8 donno why..... try vcore up to 1.53~1.54V get auto-restart or bluescreen while loading into OS rest of my rig spec oare on my siggy,, maybe need to pump more Vcore ?

ooo during 3Dmark 06 ar dragon fight area my pc hangs ....... then go back to bios set vcore to 1.5V oC to 3.32Ghz then whole com stable ran orthos for 20 minutes stable and 3Dmarks benching stable for continuesly 5 times maybe i shall stick with 3.32Ghz until Q9450 launch after CNY hehe ... last time while i'm using 3.2Ghz 3dmarks 06 was 13.2k using 8800GTS G92 ocied . Now with 3.32Ghz i get 13555 for 3Dmarks 06 woot wat an increasement

This post has been edited by Ezonizs: Jan 9 2008, 06:12 PM

guys i'm running E8400 at 4.4Ghz 489bus X 9 at 1.45v
do i need to increase my MCH and FSB voltage to get stabality ?
i'm using Gigabyte P35-DS3P Rev 1.0

wat voltage shud i use ?

This post has been edited by Ezonizs: Feb 12 2008, 11:35 PM

its an ES bro = Engineering Sample ~~~ you can get it for FREE .. just register at intel website to get an ES ~~ of coz you must have retailers shop to help you