Intel® Core(tm)2 Duo/Quad Overhauled Rev. 3, The journey continues....
|
|
 Oct 15 2007, 05:59 PM
Return to original view | Post
#1
|
 
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS  
|
Hey all , i have a question
Why i can't boot into windows when i set the FSB into 380Mhz or above ? Which factor causes me cant overclock over 380Mhz ? Btw, im using 8X multiplyer to overclock. |
|
|
|
|
|
Oct 15 2007, 09:18 PM
Return to original view | Post
#2
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
Vcore is CPU voltage ?
I push it to 1.425/1.525/1.6 and 1.8 still cant boot in...is there anything want to add volatage ?? Added on October 15, 2007, 9:39 pmoh..f***....when i push 2.0V for cpu volatage...then i saw CPU 79C then i quickly off the switch...after that...my comp cant open anymore...it will keep restart every 2 seconds....what happen? This post has been edited by 168257061: Oct 15 2007, 09:39 PM |
|
|
Oct 16 2007, 04:53 AM
Return to original view | Post
#3
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
lolx....how to resot CMOS? seems like my proc burnt
 Added on October 16, 2007, 5:23 amwahahhahahh............i plugged out the battery and can boot again...xD Later i will put it back...xD 2.0V is funny....excited...because never try it and im noob on voltage control..  Added on October 16, 2007, 5:29 amThank you guy. ok...my comp can normally boot now...just want to try again using 400Mhz fsb...so far i tried the above stated vcore still can't boot into windows...why ? This post has been edited by 168257061: Oct 16 2007, 05:29 AM |
|
|
Oct 16 2007, 10:05 AM
Return to original view | Post
#4
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(Hoodlums @ Oct 16 2007, 10:50 AM) Bro 0168257061, how about FSB Voltage? yaya....+ how many ? +0.1/2/3 ?Still default?  |
|
|
Oct 16 2007, 04:51 PM
Return to original view | Post
#5
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
Depend how far you want to go...dont push too much Vcore..dont over 1.5V is ok...yesterday i use 2.0v then my cpu fly up to 79C...
 ...nearly fry it... |
|
|
Oct 30 2007, 02:53 PM
Return to original view | Post
#6
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
1 small question here, after i use manual voltage mode in BIOS setting, there shows me the " Voltage not optimized" like this....and i save it. After reboot, it
also shows the "volatage not optimized". How to optimized it @ 1.425V or ++/-- ?? Btw my board is P35-DS3. tried 2.0v before, it its optimized but others cant.  |
|
|
|
|
|
Oct 30 2007, 07:41 PM
Return to original view | Post
#7
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(kmarc @ Oct 30 2007, 04:16 PM) Just ignore it. As long as you correctly set your voltages, that shouldn't be a problem..... it is the same with my DS3, any minor tweaking of the voltages will cause that message to appear.... oh man...   Ok...2nd....this thing make me very not impressive with my pc....i cant even push into 380Mhz or higher...when using 370mhz bus...i will automatically restart when logged in to windows. I also got +0.2V into FSB voltage and +0.2v into ram voltage. Vcore 1.425V also no use  Added on October 31, 2007, 8:24 pmhelp This post has been edited by 168257061: Oct 31 2007, 08:24 PM |
|
|
Nov 1 2007, 11:03 AM
Return to original view | Post
#8
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(kmarc @ Oct 31 2007, 10:22 PM) What is your setup - rig and overclocking? Make sure your ram is not the cause by lowering the ram divider/speed to the lowest you can set (for now)...... FSB: DRAM = 1:1 loh...wait...i post the CPUZ here later 5mins more nah..heres the cpuz.. This post has been edited by 168257061: Nov 1 2007, 11:10 AM |
|
|
Nov 1 2007, 11:28 AM
Return to original view | Post
#9
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(gengstapo @ Nov 1 2007, 12:12 PM) try l0osen the ram timing 5-5-5-15 2T ok...after to 5-5-5-12 then...what should i do? |
|
|
Nov 1 2007, 11:53 AM
Return to original view | Post
#10
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(gengstapo @ Nov 1 2007, 12:39 PM) try higher clock or torture ur system to c the stability still cant push to 380Mhz or higher......isit my psu problem? i use 400 also cant, 420/430 also cant  |
|
|
Nov 1 2007, 06:37 PM
Return to original view | Post
#11
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(kmarc @ Nov 1 2007, 05:14 PM) Your rams are running at 1:1 ratio and I see your rams are DDR667. So if you put at 380mhz, the rams will run at 760mhz, which might be the reason why you couldn't OC higher. Go to bios, and set the ram ratio to 2.0. This way, you'll have more room to overclock.... um...got 2.0/2.4/2.5/3.0/3.33/4.0 isit ?Im using 2.0 already..cant go lower T.T |
|
|
Nov 1 2007, 07:00 PM
Return to original view | Post
#12
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(kmarc @ Nov 1 2007, 07:42 PM) Ouch. That means your OC is probably limited by the rams. 2 options - loosen the rams further (e.g. 6-6-6-18, but NOT recommended) or increase the Vdimm e.g. from 1.8v to 2.0v. However, playing with vdimm will increase the risk of damage. Make sure you have fans blowing on the rams.... Hm...isit cause by my ram ? Because 1 using Hyundai chip another is Kingston....Somebody said that all DDR2 rams are warrantied until 2.2v..... dunno true or not.... ...haih...bad mood....got something happen with my gf... processor/ram burnt nvm...buy again...company sponser. |
|
|
Nov 1 2007, 07:57 PM
Return to original view | Post
#13
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(kmarc @ Nov 1 2007, 08:44 PM) Maybe, but not because of different brands. It may be because of different overclocking capabilities. If you don't mind burning the rams, then you can increase the vdimm a bit and see..... from 1.8v to maybe 2.0v.....Again, all this is AT YOUR OWN RISK..... errr... maybe at your company's risk.... haha..okk..im using 1.3875V for Vcore, +0.2V for DRAM, +0.3V for FSB voltage.... Errr..... better sort out your gf problem first la..... OC can come later....  try to push now....  I know all this is my own risk aiks...stil can't...maybe this is my limit already ...  This post has been edited by 168257061: Nov 1 2007, 08:13 PM |
|
|
|
|
|
Nov 2 2007, 12:35 AM
Return to original view | Post
#14
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(sukhoi37 @ Nov 2 2007, 12:33 AM) thanks for the info. T.T wuwuwuwu....get G0 for the E6750 ok? it's time to throw myself into the oc world again.  not like mine...-.- what the crap  |
|
|
Nov 2 2007, 09:18 AM
Return to original view | Post
#15
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(sukhoi37 @ Nov 2 2007, 09:03 AM) how to check the G0? hm..i think for now E6750 is G0 is it written on the processor ? Dont't worry. |
|
|
Nov 8 2007, 02:26 PM
Return to original view | Post
#16
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(bryanyeo87 @ Nov 8 2007, 05:05 AM) E2140 @ 3056ghz Stock Volts, Batch: Q722A025 mind to tell which PSU you using ? Patriot DDR2 667 5-6-5-15 Stock Volts Gigabyte P35 DS3 Stock Intel HSF [attachmentid=326387] -Absolutely Stable and not a suicide run -cant get past 385x8 with stock volts all Stock Volts ? |
|
|
Nov 15 2007, 09:55 AM
Return to original view | Post
#17
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
hmm..anyone E4400 can past 400Mhz FSB with L2 stepping ? I want to know.....
|
|
|
Nov 26 2007, 11:25 PM
Return to original view | Post
#18
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
Anyone E4300/4400/4500/4600 can go up 400Mhz FSB or more ? Im able to push untill 360Mhz only
|
|
|
Dec 2 2007, 03:39 PM
Return to original view | Post
#19
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
anyone here can teach me how to flash BIOS with my P35-DS3, im using F3 bios now, i want to flash F6...how ?
 noob here |
|
|
Dec 2 2007, 04:49 PM
Return to original view | Post
#20
|
|
All Stars
14,242 posts Joined: Jul 2007 From: JAVABUS
|
QUOTE(bryanyeo87 @ Dec 2 2007, 04:52 PM) http://tw.giga-byte.com/Support/Motherboar...eflashBIOS.aspx after downloaded, just double click it ?take your pick personally i prefer to flash from dos |
|
Topic ClosedOptions
|
| Change to: |  0.0387sec
 0.39
 7 queries
 GZIP Disabled
Time is now: 10th December 2025 - 12:14 PM |
Quote