Hi Team,
First of all thanks for this interesting threads. I'm newbie to this forum. I've attempt to do this change from ONU to GPON SFP after following this thread. Bought 1 sercomm Fgs202 and have 1 unused Fortigate 500D.

Action Taken:

1. Captured SLID password from current I-240G-P ONT
2. Tested setup fortigate 500D with pppoe account ( I-240G-P ONT > Fortigate [RJ45] ) successful
3. Plugged in sfp fgs202 in fortigate' sfp port, with fiber inserted light turns ON and detected on webui

Issue : sfp couldn't established WAN connection with pppoe , if not mistaken as advise here before need to change the SLID password inside sfp.
Kindly seek advice on how to access the sfp fgs202 to change the SLID password. I believe this fgs202 don't have webui, need to telnet or something sorry if Im wrong. But not sure how .Hope to learn something during this MCO

Thanks all

[quote=amirsubhi,Jan 17 2021, 01:46 PM]
Have u try telnet to 192.168.2.200/24 and run "set gpon_password YOURSLIDHERE"

Based on picture here, the GPON LAN IP is set as 192.168.2.200 https://forum.openwrt.org/t/support-for-gpo...fp-fgs202/42641

[/quote

Hi ,

GPON LAN IP is set as 192.168.2.200 in fortigate sfp port 3 interface as below

https://pictr.com/images/2021/01/17/7TpUEQ.md.jpg

https://pictr.com/images/2021/01/17/7TpiV1.md.jpg

but telnet to the IP from putty still failed. tested without fiber inserted , will try telnet again later with fiber in.

Hi,

earlier I've tested connection like from ONU I-240G-P > connects into fortigate sfp port with RJ45 through Cisco GLC-T can dial up PPPoE and VLAN 500 set in as WAN interface successfully.
Only when I bypass ONU I-240G-P and directly plug in fiber through Fgs202 sfp in the same above interface, the PPPoE dial up failed. Thanks



https://pictr.com/images/2021/01/17/7Tp1fq.md.jpg

https://pictr.com/images/2021/01/17/7TpLrr.md.jpg

Hi all,

successfully tested V2801F into Fortigate 500D. thanks to Anime4000 to initiate this idea and other members who share guides here. personally myself 1st timer in this whole process, good learning

1. V2801F brought from Russia, rm320 + shipping , almost 2 month+ to receive
2. Earlier brought sercomm FGS202 from France no WebGui , couldn't make it run & not able to telnet
3. V2801F with WebGui easy just entered SLID password from TM's GPON ONT Alcatel-Lucent I-240G-P , need to convert from Hex to Ascii

ok sure, will try to get a heat sink soon. Now the gpon sfp temperature ard 42°C . thanks

no rich lh bro. bought it RM 1.6k after good bargain+nice seller 👍. unit from a company that wound up.

Hi , can help advise how to set it through fortigate when involving this DVG-5004S. currently internet working no issues. 2 phone lines running through modem also working, only additional 2 more phone line through DVG-5004S is still down.

1. I've try created vlan400 separate interface port and bridge vlan400 together with vlan500 unifi. and also set allow policy vlan400 to outgoing interface vlan500(wan)

think im still missed out something out wrong somewhere in my setup.

please help advise , thanks

Hi Team,

recently i tested again plug-in the same sfp v2801F as before in FGT 500D but with few changes based on TM provided new gpon modem (ZTE ZHXN F620) but not working any more. pppoe connected (after waiting little longer time) but connected with very slow speed (ard 30mbps) only, subscribed 500mbps TM Unifi . the only changes i did was using new modem mac add, model , software version etc...others remain same if im not mistaken. I follow our cikgu @Anime4000 guide in github.com as usual. below are the config :

flash set GPON_PLOAM_PASSWD 1234567890
flash set GPON_SN ZTExxxxxxx
flash set GPON_ONU_MODEL F620
flash set OMCI_TM_OPT 0
flash set VLAN_CFG_TYPE 1
flash set PON_VENDOR_ID ZTEG
flash set OMCI_SW_VER1 V9.0.10P4N2
flash set OMCI_SW_VER2 V9.0.10P4N2
flash set CUSTOM_OMCI_SW_VER1 V9.0.10P4N2
flash set CUSTOM_OMCI_SW_VER2 V9.0.10P4N2
flash set HW_HWVER V7.0
flash set ELAN_MAC_ADDR f864b8bf8a74
flash set VS_AUTH_KEY DD4D14B4773F74DF18F742E1A0E3673D
flash set OMCI_FAKE_OK 1
flash set OMCI_OLT_MODE 1

not sure where i did mistake....need some help thanks team

Hi Team,

recently i tested again plug-in the same sfp v2801F as before in FGT 500D but with few changes based on TM provided new gpon modem (ZTE ZHXN F620) but not working any more. pppoe connected (after waiting little longer time) but connected with very slow speed (ard 30mbps) only, subscribed 500mbps TM Unifi . the only changes i did was using new modem mac add, model , software version etc...others remain same if im not mistaken. I follow our cikgu @Anime4000 thumbsup.gif guide in github.com as usual. below are the config :

flash set GPON_PLOAM_PASSWD 1234567890
flash set GPON_SN ZTExxxxxxx
flash set GPON_ONU_MODEL F620
flash set OMCI_TM_OPT 0
flash set VLAN_CFG_TYPE 1
flash set PON_VENDOR_ID ZTEG
flash set OMCI_SW_VER1 V9.0.10P4N2
flash set OMCI_SW_VER2 V9.0.10P4N2
flash set CUSTOM_OMCI_SW_VER1 V9.0.10P4N2
flash set CUSTOM_OMCI_SW_VER2 V9.0.10P4N2
flash set HW_HWVER V7.0
flash set ELAN_MAC_ADDR f864b8bf8a74
flash set VS_AUTH_KEY DD4D14B4773F74DF18F742E1A0E3673D
flash set OMCI_FAKE_OK 1
flash set OMCI_OLT_MODE 1

not sure where i did mistake....need some help thanks team

salam bro,

still connect with low speed (30-40 mbps) , i did try few combinations also like changing omci_fake 1/0 and omci_olt 0/1 together with OMCI_TM_OPT 1/2.