~44c - 46c, both cores at 100% load using F@H.

Cedar Mill was way better than Conroe-L in terms of OC... but not for normal use...

Cedar Mill can't win over Conroe at all...

*Cedar Mill = Celeron 3 series
*Conroe = Core 2 Duo
*Conroe-L = Celeron 4 series...

mind defind the terms below??

*Cedar Mill = Celeron 3 series
*Conroe = Core 2 Duo
*Conroe-L = Celeron 4 series...

i only know there are prescott, cedar mill, allandale and conroe. dunno about conroe-L, celeron 3 and 4 series....

i onli able to OC my cedar 3.0 up to 3.75g onli..more than tht kenot boot oredi..heh amateur work

i mean, conroe is way better than cedar mill, due to the architecture difference
even u never overclock ur conroe, there is always a big chance a 1.8ghz conroe will smoke a 3.x ghz cedar

wats ur speed and vcore? and the HSF? kinda nice temperature

mm..i`ll try to do prime test this weekend..see how`s my temp..

2150mhz
vcore 1.35
stock heatsink

btw guys, i thought that if i disable EIST then the multiplier and vcore won't jump around already. mine still jumps around.

I believe u disable all the spread spectrum/EIST?
Maybe its the time to try Polygon's mod bios.

If not because of the ram divider issue, you should be able to clock 2.5ghz or more with stock hsf @ stock vcore on e2140.

ok thanks for the info

here`s mine http://valid.x86-secret.com/show_oc.php?id=228862
cant pass prime85..do i need to increase the cpu vcore?

atleast this one can run prime test http://valid.x86-secret.com/show_oc.php?id=228873

This post has been edited by fesick: Aug 13 2007, 11:42 PM

err... DDR800 can go further... i play around 500MHz since my GA-965P-DS4 & Corsair XMS2 1GBkit(512MBx2)...
Here is a cincai OC juz to show how easy it is to be more than 400MHz...
Here's my another OC under testing... which i 4got to turn off EIST and all those crap...

Now tat i done some OC and tested in a few hardwares... i notice tat cheaper performance RAMs doesn't give tat much of edge to higher level OCers... but hey... they are still cheap... actually i wanted to order the Mushkin HP or Redline series but Mushkin haven't start importing those yet... even EM series also very limited which can be found in Low Yat which is also quite rare... wait until my next Hdd arrive then i can start assembling my old parts into my 2ndary rig... for "downloading" purpose... and see E2160 wif Corsair XMS2 1GB(2x512MB) kit DDR667 n my 1 year old GA-965P-DS4...

This post has been edited by t3chn0m4nc3r: Aug 14 2007, 04:19 AM

yeah. divider issue lor.

and last i check Polygon's mod, even though 400 / 533 mhz setting available, it doesn't cure the divider issue.


you don't get what i mean. of course we all know DDR2 800 can go even more, but point is i don't need it already when my DDR2 667 can already do DDR2 900 speed.

polygon mod?whats that?mind to share..

i'm new here becos there's some1 suggest me to oc my e2140 with my p35 ds3 board, any link site for me as reference or guide?

thanks

u may check at his thread. various of ocing tips and hints u can find here:

http://forum.lowyat.net/OverclockersUnited

u got good Mobo and proc, don't waste them by running on stock...

add more vcore, jus make sure the temperature is ok, up to 1.4V is ok for stock heatsink i think

err... no... actually 667 can also go up to 1000... wait until i rebuild my BT rig from my old parts than i show u... already have a E2160 at hand... now it's a matter of my next HDD... Hynix, Samsung, Micron & Mushkin shouldn't have much problem wif tat...
n i came to realize tat either my mobo, proc or temp is bottlenecking my OC... my RAM can't seem to go higher than this at the same timing...

This post has been edited by t3chn0m4nc3r: Aug 15 2007, 12:47 AM

aih you ah. i'm not here to say how far it can go la cos i'm just talking about MY RAM. furthermore it depends on chip.

for now i'm just happy to see mine touch DDR2 900.

Netburst architecture will be better than conroe if the clock speed is 90~100% more. What a shame...