No problem dude .. even a non modular high end power supply could fit in without sweat ...

Weird ... I had the same case before but it looks black from the photo taken ..

It was taken with a 5mp casio dc .....

hhahha .. we can't care too much about their comment regarding Lian Li and their product line...

As long as we enjoyed it ... we are the one that happy about it ....

I don't care whether my gf like it or not ... but most of time ... she would say hmm no bad ... girl mah ....

hahha if u want today also u could get the info from me coz I would be going ...

hahahaha ... Bezel and BS-02 right ??? price & availability ... no problem ...

This post has been edited by Doom: Jul 6 2007, 08:50 AM

hahaha .. I've read that long before .... couple years back before ..

He could get such mirror shine out of patience and right polishing liquid...

If u use Autosol U can't get the same detail or shine like him...

Autosol just not fine and detail enough ... u could PM Cableguy what kind of polisher he uses and where he got it ...

Hhaha ..Normally I don't need to switch off my PSU .. coz usually I just unplug all the plugs connected to the power socket.

Yah u need to remove the front panel to gain access to the power switch behind of the PSU ....

Anyway just got back from ATE today ... BS-02 still out of stock and Billy said he's trying to get some and he wants me to confirm how many units that LYN forumer wants .... so that he could be certain how many units to bring in ....

as for the CD-ROM bezel there are plenty for black at the price of RM35 each ...so go grab it while stock last ....

Using Autosol only allowed u to polish it back to the way it is but not mirror shine .... it just can't .. I tried myself ... an hour long polishing the surface of an aluminum but it just won't shine likes mirror.....

I tried modeling kit's polisher and it works better in term of getting better polishing result but it's still far from mirror shine....

Sure ....

It's RM55 or RM50 ... I could confirm later ...

Anyway ...for those that not confirm about the compatibility can PM me ....

I would check it out for u guys ....

Yah and in fact I took one behalf the owner today ..

This is the owner trying to lift the case ..... seems like Lian Li's case is really light enough...


His ex case .. CM 530


Installed case...







Owner locking up the side panels...




Here is the official owner of the case .... He's 7 years old only ... yah no cheating .... at all

This post has been edited by Doom: Jul 7 2007, 11:14 PM

I heard about Lian Li when it was first introduce here back around 1998 ...

I'm not sure that's the Lian Li case or not but it should be coz it's the only case at that time that comes in full aluminum without PSU yet cost RM800 per unit ...

My brother told me how he wished to grab one of those ... but too bad until now .. he's still using CM 530 only ...

@akachester, Hyde`fK, E-J@1

hehehe ,, the two fans are joined with zip tie ...

Then it's tight to the rear exhaust holes with wire strip...

And there are two PCI slot bracket that screwed at the bottom of the fan as supporter .. .most won't realized it ..

hheheh look carefully in the picture ,,, there's a bit of shine at the bottom of the fans...

There's no side blow holes were done coz there's no need for the passive cooling 7300GT .... the dual fan already more than enough to cool off the card..

Besides the owner only play simple 3D game with the rig .. it just can't torture the card too much ....

This post has been edited by Doom: Jul 8 2007, 09:23 PM

hmm u could fit in if the gap is less than 5 mm ...

or u could place the PSU up side down ....

Most likely it will be able to fits in ... as long as u don't tight the thumb screw so deep down ...

Yah it could tolerate and fit in ,,,, but the best would be u bring the PSU to test it out ... on the safe side....

Depend u configuration ... if U would be u I would just make side patent fan serve as intake for gc and south bridge..

While the rear set to exhaust to take out the hot air taken from the top ...

yah a bit but just screws it down and there would be slight gap about 1 to 2 mm ....

so have to push the burner out slightly to match the gap ...

but there's no real problem at all coz the drive's tray able to eject properly .

is it??? U must be lucky then .. cos it takes quite some times to restock ...

Anyway any photo of ur new babe to sparkle out eyes ....

Nope it won't, I been cleaning all my cases with cleaning detergent ...

No problem at all .. coz it won't damage the surface at all ..

It just remove the dust and some oily finger prints...

@Polar_012

Are u sure it's fine for the processor to run with passive cooling on Ultra-120 ??

I thought Ultra-120 series required high CFM fan to utilize it's performance..

Anyway share some 'Cacing' over here ....

@kalakatu

Why on earth do u need to mod G7 ... it's a great case for both cable management and cooling performance...

Yah ...for the fan clips to work properly u have to apply the pin into the heatsink hole nicely before attach the fan ...

Basically the side patent fan that WebWalker refers to Lian Li own side fan frame with fan ..

There are two model BS-02, BS-03 ..there should be another one which is currently no more available ... But still could get it from some other older model ...

BS-02 draw or exhaust according to the fandiection directly ..

while BS-03 uses the fan frame as air guide to exhaust air ..

It's definitely air gear fans .. .haha I'm one of them as well ....

Sexy girl sliding through the deep green forest with their shinning wheels. ..

Anyway from the length it's V1000B Plus II ....

nice cutting on the top .. .and I love the decal ... probably I should get one with other design for the other side of my A05 ..