> Supports IPTV
> Powered by Android TV
> Amlogic S905C1 chipset
> ARM Mali-G31 GPU
> 2GB DDR4 RAM
> 16GB Flash Storage
> Dolby Digital Plus
> High Dynamic Range 10
> 4K UHD Resolution

1x UPB 2.0 box
1x Remote (IR/BT)
2x AA batteries
1x AC adapter
1x 3.5mm AV cable
1x LAN cable
1x HDMI cable
1x Quick Start Guide
3x MAC address stickers
1x QC passed label

Factory firmware
Android 10
Security patch 5 Jul 2021
Kernel 4.9.180; #1 Thu Aug 12 16:17:04 CST 2021
Build QTT2.200720.001.P2.0.2_20210812 release-keys

Remote software version 0126

"Day one" (idk) update
Android 10
Security patch 5 Nov 2021
Kernel 4.9.180; #1 Fri Dec 31 15:35:11 CST 2021
Build QTT2.200720.001.P2.0.2_20211231 release-keys

Size: 815MB
Remote software unchanged

Update description

Setup is apparently similar to UPB 1.0. Required Google account login to continue, very common to be stuck at "Please wait..." (same as UPB 1.0) after connecting to LAN (VLAN probably doesn't work yet), so best to connect WiFi until setup finishes. VLAN600 IPTV can be setup later.

Initial setup will prompt to pair with BT remote. Can skip but the IR performance is very poor. LED light on UPB will flash orange to indicate IR input received but will consistently miss inputs or require double pressing buttons. Everytime startup will nag to pair BT if remote is unpaired. BT mode has 0 problems so far, Google Assistant not tested.

Box startup with unifi TV as default app. UI is same as UPB 1.0 app, so no mosaic.

(iirc have to be connected via WiFi/normal LAN first until setup is done)

Reminder that you will not get mosaic screen anymore. IPTV stream will passthrough to unifi TV app when connected to VLAN600.

1. IPTV can be enabled with the "Skyworth IPTV service" app. Launch app then press OK as prompted to launch unifi TV app.
2. If haven't logged in yet, login with playTV username and password.
3. "Replace Device" screen will appear, select old device model to replace then press Confirm. This will remove access to the old HyppTV box.

Apps (YT, BBC, iQiYi etc) will not be usable when connected to VLAN only. Enable WiFi or plug into normal LAN to use apps.

> 4k2k-59.94hz, 50hz, 29.97hz, 25hz, 23.976hz, smpte (24hz)
> 1080p-59.94hz, 50hz, 23.976hz
> 720p-59.94hz, 50hz
> 1080i-59.94hz, 50hz
> 576p-50hz
> 480p-59.94hz (no video/audio signal when tested with 4K TV)

> Cannot connect 3.5mm AV together with HDMI. Spacing is too close
> Adding Google account took >5 mins of loading
> Can check but couldn't download firmware update with custom router (LAN/VLAN/WiFi). Had to use TM router to download
> Some TVs may randomly flash 3-5 times before losing video signal (HDMI). May need to restart box then disable "Auto switch to best resolution"
> No sideloading of apps, even with app installer downloaded from Play Store
> Can access Developer options with Roy Solberg's app (applink) but USB debugging is disabled. Be careful to not turn off Developer options toggle otherwise it will also be disabled
> Encountered very strange message. When adjusting YT subtitles a message appeared "This operation cannot guarantee the safety of the device. Continue?" OK/Cancel is shown, but ~5 seconds later OK is automatically highlighted then disappeared. Was watching YT app and adjusting subtitle size on latest "day one" FW and YT version. BT remote and DS4 controller were connected, not sure what changed