If it looks, walks and quacks like a duck? It's a duck! So yep, I'd say it's the exact same hardware, except with different stickers.

I wish unifi gave me this instead of that stupid dlink which spoil less than 3 month use!!! Is this also loaded with unifi custom firmware?

Yeah, depending on your area, there may or may not be adequate stock of better routers from TM. So unfortunately, we either have to rely on it as is and hope all good or cough up extra money to get a better third party router.
Have 2 units, one is almost 3 years old and the other is almost a year old.. Max Wi-Fi speeds even via 5GHz remains at 2xxMbps, which is sufficient for my wireless devices. Other network intensive devices are wired and receive full 500Mbps. Fingers crossed mine doesn't go kaput. So far so good..

I had many bad experience with dlink no more dlink for me lol!

I used to have & use the DIR850L. Worked fine, no random reboots as far as I could tell....only downside is the subpar wifi signal strength and coverage.

Internal antennas not always mean limited Wife coverage/performance. They're routers/APs with good coverage/performance eg TP-Link Deco M9, D-Link DIR-868L, Ubiquiti Unifi UAP etc.

hi, does the new revision of TP-Link Archer C1200 with new TP-Link Logo and new unifi Logo instead of TM Logo still suffer from random reboot, auto restart, or any other common C1200 issue?

it's still the same version of Archer C1200 v1.0 , came with 1.0.0 Build 20180403 rel.22124 (EU) firmware preinstalled out of box.

thx in adv.

it seem there is some bug at the unifi D-Link DIR-850L router 2.12TM firmware release at 2019, Dahua imou Ip Camera Cloud Live Stream would Disconnect 99% of time, While LAN and Wifi Live Stream still working 100% of time, but 6 Models, 4 Brands of newer and older generation Ip Camera Cloud Live Stream would still working well 100% of time.

tried to reset and reconfig/setting manually without config backup and upload unifi D-Link DIR-850L router, bug issue still happen.

tried to Enable UPnP: ; IPv4 Multicast Streams: ; IPv6 Multicast Streams: ; Application Level Gateway (ALG) Configuration ; PPTP: ; IPSec (VPN): ; RTSP: ; SIP: ; and Multiple Port Forwarding, work a while and Cloud Disconnect again.

Enable DMZ: work but didn't spend the times to test it for how long, but DMZ work for only single device/IP.

Tested Dahua imou Ip Camera Cloud Live Stream with TP-Link Deco M4 v2 Latest Firmware 190917 , working 100% of time.

more Detail Report here : https://forum.lowyat.net/index.php?showtopi...&#entry97021190

subscribe and install unifi fibre 30mbps at December 2017, the unifi D-Link DIR-850L router came with newer Default Firmware 2.09TM , the Sticker at the plastic router casing and package box bottom has Firmware 2.09TM written, the big multiple Realtek Chipset security issue was fixed with this Default Firmware. never tried to play with different Region firmware upload & install manually with this router, the only firmware upgrade done was 2.10TM and 2.12TM , at router web interface Check for New Firmware.

tried to Flash unifi D-Link DIR-850L with newest international Firmware 2.23 with lastest fixes, 1st Boot to D-Link Router Recovery Mode and flash Middle Firmware DIR850LB1_FW210WWb03.bin , then router web interface Upgrade Manually DIR850LB1_FW220WWb03.bin , then DIR850LB1_FW223WWb01.bin , after that Restore To Factory Default Settings and reconfig/setting manually without config backup and upload.

https://forum.lowyat.net/index.php?showtopi...&#entry86448823

http://forums.dlink.com/index.php?topic=44909.0

ftp://ftp2.dlink.com/SECURITY_ADVISEMENTS...CH_v2.20B03.zip

http://pmdap.dlink.com.tw/PMD/GetAgileFile...3494E7;19623.0;

http://pmdap.dlink.com.tw/PMD/GetAgileFile...0064E7;15877.0;

ftp://ftp2.dlink.com/PRODUCTS/DIR-850L/RE...BM8_WW_BETA.zip

with Latest international Firmware 2.23 , all [Dahua imou Ip Camera Cloud Live Stream would Disconnect 99% of time] issue was gone, now Dahua imou Ip Camera Cloud Cloud Live Stream was working 100% of time, same as all other [6 Models, 4 Brands of newer and older generation Ip Camera Cloud Live Stream would still working well 100% of time.] with all setting turned off [UPnP: ; IPv4 Multicast Streams: ; IPv6 Multicast Streams: ; Application Level Gateway (ALG) Configuration ; PPTP: ; IPSec (VPN): ; RTSP: ; SIP: ; Multiple Port Forwarding ; DMZ]

another issue happen since 2.12TM firmware also gone, System Log E-Mail, now it's also working 100% of time. this issue doesn't happen at 2.10TM firmware.

https://forum.lowyat.net/index.php?showtopi...&#entry92708171

https://forum.lowyat.net/index.php?showtopi...&#entry92708161

https://forum.lowyat.net/index.php?showtopi...&#entry92708142

the D-Link DIR-850L international firmware doesn't have TM TR-069 and other customization, router web interface is much smoother.

just realise that unifi given C1200 have this firmware version, never update it manually, but not sure and forgot is it came with this firmware or the firmware was update by TM TR-069 , however this firmware version was not available at internet. unifi biz fibre RM139 100mbps install at 2019 September.

1.0.0 Build 20190805 rel.22215 (EU)

Archer C1200 v1.0

also, even after router restart automatically or manually, the ipv4 would still stay the same, for multiple months, but ipv6 would change every restart. fibre modem is Huawei HG8240H5 ONT

if want to change ipv4, have to restart router "many" multiple times during period of few hours. but the next ipv4 would still stay the same even after router restart.

EDIT9: Apparently, a lot of users complained about WAN IP changing the next day. This was caused by AUTO selection at router PPPOE dialer. Seriously, I expect users to set On Demand when setting up the router from the beginning. (This should be common knowledge, no?  Who in the world use Auto?    ). Here the guide:


Do note the router with latest firmware still randomly reboot once every 3 - 4 weeks.......

Guys, is it possible that the infamous random reboot and WAN IP reset has a simple solution instead of upgrading your firmware?

I realized something about C1200, any AUTO settings in it are set to worst possible choice available instead of the best. This is very apparent when i select wireless channel width to AUTO, it will choose the worst choice and perform the worst. So, i guess the trick here is to manually specify exactly what you want in the settings and don't leave it as AUTO due to very poor programming in the firmware.

SO, from what i read through all the problems regarding random reboot or WAN IP resets, majority of them sounded like the trigger was idle internet activity. So then i went in to INTERNET settings, and choose MANUAL connection mode with 0 idle time and i tested. Saved settings and went to sleep. Mind you my WAN IP changes every next morning before this settings. After this settings, i was pleased to find my WAN IP is still same. I believe ON DEMAND connection mode with 0 idle time works the same.

So far so good, WAN IP sticks during idle activity, heavy torrenting, heavy streaming, lite browsing. The record so far is few days, crossing finger that this will work for the entire month ! 

goto Advanced, Internet, Advanced. Set connection mode to On Demand and Max Idle Time to Zero. Save.
[attachmentid=10074643]

Does anyone have firmware Version 1.0.0 Build 20190320 rel. 5557 (EU)?

just realise that unifi given C1200 have this firmware version, never update it manually, but not sure and forgot is it came with this firmware or the firmware was update by TM TR-069 , however this firmware version was not available at internet. unifi biz fibre RM139 100mbps install at 2019 September.

1.0.0 Build 20190805 rel.22215 (EU)

Archer C1200 v1.0

also, even after router restart automatically or manually, the ipv4 would still stay the same, for multiple months, but ipv6 would change every restart. fibre modem is Huawei HG8240H5 ONT

if want to change ipv4, have to restart router "many" multiple times during period of few hours. but the next ipv4 would still stay the same even after router restart.

Hi guys there is a firmware update available for this router from Unifi. Just called the customer service on Wednesday and they told me there's an update available which is the 20201103 version. Previously it was on 20200306. Just got this router from Unifi in December 2020. After the latest firmware upgrade, it has been 3 days now and there's no random reboot happen. Hope this info will help you guys

Nope you need to call the customer service and ask them for the latest firmware version. They will send your request to their support team for them to upgrade the firmware remotely from their side. Mine was done within less than an hour. The latest firmware version is 1.0.0 Build 20201103 rel.11985(EU).

New firmware found on TP-Link AC1200 Malaysia page. This is for hardware V1.

Maybe for Frag Attack patch? 

Are you sure it's a new firmware? The file name seems to indicate Build 20200306 rel.15999_2020-03-06 which roughly translates to March 2020. Anyway, I checked my firmware version and it's the same as this. I'm sure I did not perform any firmware update on my router before.

How did you resolve this?

hi, there is some unifi router newer internal firmware that are not available to download elsewhere, from tm staff posted to public.

https://sts2u.com/download-firmware-terkini/

https://sts2u.com/matrix-penggunaan-tm-cpe-...i-rujukan-anda/

TM CPE Model Latest Firmware

SBVM Netis DL4480V1 DL4480V1_2.0.9e_20200206_1527_sig.img

SBVM Netis DL4480V2 DL4480V2_V3.1.11

SBVM Aztech DS244WSGV DS244WSGV_V1.0.4_21012020.img

SBVM TPLink VR1200V Archer_VR1200vv1_1.0.0_0.8.0_up_boot(181024)_2018-10-24_16.21.45.bin

RG DLink DIR-842 3.DIR842TMC1_FW307TMb01.bin07TMB01

RG TPLink Archer C1200 1.0.0Build20210727rel.5533

RG ZTE H288A V1.1.0C4_TM

RG OTS DLink DIR-825 DIR-825M_V1.1.8_upgrade_Final_Security.bin

RG OTS DLink DIR-830 V1.1.1

RG OTS FiberHome SR120A SR120-A_INTL_Image_202104271200.bin

RG OTS TPLink Archer C6 1.3.6 Build 20200902 rel. 65591 (4555)

RG MWG Aztech WR744WSGV-V3 WR744WSGV-V3_V3.0.3

RG MWG Dlink DVG-F2452 ver3.0.4

RG MWG TPLink EC221 EC221-G3v_3.0.0