Omg, i would need to take note on this to prevent the glue sick on my back case or back of my iPhone. I remember during my iphone 7, if i tape it always, the word behind the phone will be faded. Ops.
Hmm I think on 8/x glass back the word wouldn't fade off...but in long run I'm not sure lol...perhaps get better quality cellotape? I'd rather tape the parts exposed on casings ie charging ports, speakers, mute button and etc....those are the massive dust spots..
But till now I still use cotton clothes to wipe off dusts...even on spots like bottom speakers/ charging port...and u know stainless steel doesn't go well with dust...
This post has been edited by dikae: Dec 25 2017, 03:05 PM
Hmm I think on 8/x glass back the word wouldn't fade off...but in long run I'm not sure lol...perhaps get better quality cellotape? I'd rather tape the parts exposed on casings ie charging ports, speakers, mute button and etc....those are the massive dust spots..
But till now I still use cotton clothes to wipe off dusts...even on spots like bottom speakers/ charging port...and u know stainless steel doesn't go well with dust...
Other than that, i realised inside my speaker holes got some dust, how am I going to remove it? Any idea?
Other than that, i realised inside my speaker holes got some dust, how am I going to remove it? Any idea?
Normally I'll use baby cotton buds..those extra small size and put it in the holes and do some light twist..but make sure don't put water, do it dry and not too hard..it helps abit and not much, but better than nothing..just do it like once a week/2 weeks so that dusts won't accumulate..
Normally I'll use baby cotton buds..those extra small size and put it in the holes and do some light twist..but make sure don't put water, do it dry and not too hard..it helps abit and not much, but better than nothing..just do it like once a week/2 weeks so that dusts won't accumulate..
I used to blow it, but the dust still there. I dont have baby cotton buds though.
I used to blow it, but the dust still there. I dont have baby cotton buds though.
Not hard to find baby buds...u can get them at the supermarket or pharmacy
Another way I have tried before is to stick cello tape on the speaker....then use baby buds (remove the cotton) so u will have only the stick and press it on the cellotape against the speaker holes..but not too hard just light ones will do..works all the time...but I only do it when here are lots of dust accumulated...
This post has been edited by dikae: Dec 25 2017, 03:50 PM
Not hard to find baby buds...u can get them at the supermarket or pharmacy
Another way I have tried before is to stick cello tape on the speaker....then use baby buds (remove the cotton) so u will have only the stick and press it on the cellotape against the speaker holes..but not too hard just light ones will do..works all the time...but I only do it when here are lots of dust accumulated...
Sounds like a good idea. I will try tomorrow. Going to get the cotton bud from supermarket. Thanks for teaching though.
Gg, i keep on looking at the speaker now. Tried to suck it with my mouth, not working lol. Hahahaha
QUOTE(kyogre @ Dec 25 2017, 03:59 PM)
dei this is how u get crabs
Hahahha noooo don't suck it bro ..dust can't be vacuumed out that way....and even if u blow make sure u dry your mouth or else salivas get into speaker is another issue there..
Hahahha noooo don't suck it bro ..dust can't be vacuumed out that way....and even if u blow make sure u dry your mouth or else salivas get into speaker is another issue there..
Lol hahahaha, cant wait for tomorrow or later to get the dust out.
» Click to show Spoiler - click again to hide... «
Full adhesive
Full adhesive usually will be best on clear SP. But the problem is around the edge can seen bubble due to 2.5D curved screen. But I will tried with 4D full screen protector for help and covered the whole screen.
Spray with liquid on screen for clean out those dirt, before wipe it dry.
Usually I would used with 3M transparency tape to stick up those micro dirt before paste with SP.
This is the one 5D full adhesive sp.
All done without any bubble on the screen edges.
How’s the SP so far? Is it prone to fingerprint smudges?
How’s the SP so far? Is it prone to fingerprint smudges?
Got Oleophobic coating helps resist oils and fingerprints, if whole day usage still can spot fingerprint or oily base on screen surface, the good thing is easier to clean with micro fiber cloth. Once wipe over without any water marks leave on screen surface.
Dec 25 2017, 03:04 PM
I'd rather tape the parts exposed on casings ie charging ports, speakers, mute button and etc....those are the massive dust spots..
Quote
thanks..
0.0267sec
0.55
6 queries
GZIP Disabled