Welcome Guest ( Log In | Register )

12 Pages < 1 2 3 4 5 > » Bottom

Outline · [ Standard ] · Linear+

 Tutorial on Ubiquiti Edgerouter for unifi/maxis, Edgerouter settings ftw

views
     
TSwanttotree
post Jan 7 2017, 04:32 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
I was thinkin u were to get erl+ts5poe+lgs108. I hope u understood. U did mentioned a few options, but its your decision 100% to buy which one.
kutitata
post Jan 8 2017, 03:33 PM

Casual
***
Junior Member
322 posts

Joined: Dec 2007
QUOTE(wanttotree @ Jan 7 2017, 04:32 PM)
I was thinkin u were to get erl+ts5poe+lgs108. I hope u understood. U did mentioned a few options, but its your decision 100% to buy which one.
*
Yea, I agree I am being going through so many options...

I mean to be honest they all cost almost the same...

Would a ERL+TS5POE+LGS108 be better than a ERPOE5+LGS108? I know you explain me it to me so many times...

blink.gif

Another question, how do we set up the UAP AC LR that the clients will keep re-connecting to the AP that is closest to them?
TSwanttotree
post Jan 17 2017, 06:51 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
QUOTE(kutitata @ Jan 8 2017, 03:33 PM)
Yea, I agree I am being going through so many options...

I mean to be honest they all cost almost the same...

Would a ERL+TS5POE+LGS108 be better than a ERPOE5+LGS108? I know you explain me it to me so many times...

blink.gif

Another question, how do we set up the UAP AC LR that the clients will keep re-connecting to the AP that is closest to them?
*
Sorry bro, i was on vacation. Im back. Yes it would be better. I recommended u that because i dont want to confuse u with more setups. So u can go ahead use erl+tspoe5+lgs108.

To get load balancing aps can be done if u applied a unifi controller. Either u get one from unifi, or install one via linux on any used pc and serve as one. Keep in mind, lr is long range, so usually ppl dial down minimum rssi so it will disconnect once signal is low, and look for closest one. The uap ac lr does not support seamless roaming, so u gotta set rssi manually to make it work.(yes, all ac versions dont support seemless roaming)

This post has been edited by wanttotree: Jan 17 2017, 06:58 PM
irwan6179
post Jan 18 2017, 03:12 PM

Regular
******
Senior Member
1,036 posts

Joined: Oct 2004
From: the other side



Can it just be setting the SSID/password the same? With proper rssi i think we can achieve the so-called seamless roaming.
TSwanttotree
post Jan 18 2017, 03:26 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
QUOTE(irwan6179 @ Jan 18 2017, 03:12 PM)
Can it just be setting the SSID/password the same? With proper rssi i think we can achieve the so-called seamless roaming.
*
Yes u r right good sir. As simple as that. Thats y sometimes lr is giving more problems than solution when it comes to multiple ap.(more expensive is in some cases)
TSwanttotree
post Jan 21 2017, 04:20 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
Hey guys, i will be free around next week. I am planning to write another tutorial on edgerouter. How bout ipv6 for unifi? Or hypptv and internet using one single port?(not tested yet). Vlan tagging for guess network? I will be writing one based on requests.
Shaney
post Feb 3 2017, 02:39 AM

Getting Started
**
Junior Member
254 posts

Joined: Nov 2008
From: Heart <3



QUOTE(wanttotree @ Jan 21 2017, 04:20 PM)
Hey guys, i will be free around next week. I am planning to write another tutorial on edgerouter. How bout ipv6 for unifi? Or hypptv and internet using one single port?(not tested yet).  Vlan tagging for guess network? I will be writing one based on requests.
*
Hi there.
It seems like e could tag vlan on wireless.

I wonder is it possible for us to tag vlan 600 for ip tv through wifi?
kutitata
post Feb 7 2017, 02:29 PM

Casual
***
Junior Member
322 posts

Joined: Dec 2007
looking forward to your next tutorial wanttotree
TSwanttotree
post Feb 11 2017, 06:27 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
I was waiting for responds here for a while before i decided. Anyway, i think i will come up with ipv6 tutorial soon. The tutorial is basically as simple as copy and paste in the ssh terminal. So stay tuned. =)
kutitata
post Feb 23 2017, 07:56 AM

Casual
***
Junior Member
322 posts

Joined: Dec 2007
QUOTE(wanttotree @ Feb 11 2017, 06:27 PM)
I was waiting for responds here for a while before i decided. Anyway, i think i will come up with ipv6 tutorial soon. The tutorial is basically as simple as copy and paste in the ssh terminal. So stay tuned. =)
*
nod.gif
bear1305
post Feb 27 2017, 04:43 PM

New Member
*
Junior Member
34 posts

Joined: Oct 2004
From: Selangor.



Hi..

Any idea if I have setup my ER-X using load balance and currently running on a Time Broadband connection. How do I set it up to use it with a TM Unifi? Can I add in the vlan directly to the eth port to accept a Unifi connection?
TSwanttotree
post Feb 27 2017, 07:32 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
Yes , u can bro. Just update to 1.9.1 then follow the instruction. Or u can manually add new connection by;
Delete previous pppoe connection(time). Then add vlan 500. Then add another pppoe under ethx.500. lemme know if u cant find them.

This post has been edited by wanttotree: Feb 27 2017, 07:33 PM
bear1305
post Mar 1 2017, 03:07 PM

New Member
*
Junior Member
34 posts

Joined: Oct 2004
From: Selangor.



Hi..

I'm on 1.9.1 currently and already setup using Load Balance; not the one with vlan. But only one pppoe used currently. The 2nd pppoe is currently disconnected. I plan to use the 2nd pppoe with Unifi.

So, can I add the vlan to the eth port directly or need to setup from scratch again?


TSwanttotree
post Mar 1 2017, 03:15 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
QUOTE(bear1305 @ Mar 1 2017, 03:07 PM)
Hi..

I'm on 1.9.1 currently and already setup using Load Balance; not the one with vlan. But only one pppoe used currently. The 2nd pppoe is currently disconnected. I plan to use the 2nd pppoe with Unifi.

So, can I add the vlan to the eth port directly or need to setup from scratch again?
*
Yes u can add vlan easily. Just add vlan interface, then add pppoe on top of that.
pandera999
post Mar 1 2017, 11:36 PM

모든 것​에는 정해진 때​가 있으니
*******
Senior Member
6,195 posts

Joined: Sep 2010
From: Busan, Kr | Kuching, Swk



thumbs up.. bookmark
TSwanttotree
post Mar 2 2017, 01:42 AM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
QUOTE(pandera999 @ Mar 1 2017, 11:36 PM)
thumbs up.. bookmark
*
Hey thanx man. Meant a lot to me. Cheers
bear1305
post Mar 2 2017, 10:26 AM

New Member
*
Junior Member
34 posts

Joined: Oct 2004
From: Selangor.



QUOTE(wanttotree @ Mar 1 2017, 03:15 PM)
Yes u can add vlan easily. Just add vlan interface, then add pppoe on top of that.
*
Hi..

Noted, thanks. Will try on that.

By the way, one more question, my setup is as below:-
eth0 - switch0.110, switch0.120, switch0.130
eth1 - pppoe1
eth2 - pppoe2
eth3 - switch0.110, switch0.120, switch0.130
eth4 - not configured anything

I tried configuring eth4 to assign IP by DHCP without any vlan. But, it doesn't seem to assign an address and I can't access internet.

I also tried being on a static address 10.20.100.100 as my ER-X gateway address is on .251, and I'm plugged in to port eth0 and yet no access to internet.
But, at same time, I have traffic coming in from eth3 via vlan 110, 120 & 130 without any problem accessing internet.

Am I missing out something here?


TSwanttotree
post Mar 2 2017, 03:13 PM

On my way
****
Junior Member
650 posts

Joined: Apr 2008
QUOTE(bear1305 @ Mar 2 2017, 10:26 AM)
Hi..

Noted, thanks. Will try on that.

By the way, one more question, my setup is as below:-
eth0 - switch0.110, switch0.120, switch0.130
eth1 - pppoe1
eth2 - pppoe2
eth3 - switch0.110, switch0.120, switch0.130
eth4 - not configured anything

I tried configuring eth4 to assign IP by DHCP without any vlan. But, it doesn't seem to assign an address and I can't access internet.

I also tried being on a static address 10.20.100.100 as my ER-X gateway address is on .251, and I'm plugged in to port eth0 and yet no access to internet.
But, at same time, I have traffic coming in from eth3 via vlan 110, 120 & 130 without any problem accessing internet.

Am I missing out something here?
*
Please post yr config bro.
pandera999
post Mar 2 2017, 03:15 PM

모든 것​에는 정해진 때​가 있으니
*******
Senior Member
6,195 posts

Joined: Sep 2010
From: Busan, Kr | Kuching, Swk



QUOTE(bear1305 @ Mar 2 2017, 10:26 AM)
Hi..

Noted, thanks. Will try on that.

By the way, one more question, my setup is as below:-
eth0 - switch0.110, switch0.120, switch0.130
eth1 - pppoe1
eth2 - pppoe2
eth3 - switch0.110, switch0.120, switch0.130
eth4 - not configured anything

I tried configuring eth4 to assign IP by DHCP without any vlan. But, it doesn't seem to assign an address and I can't access internet.

I also tried being on a static address 10.20.100.100 as my ER-X gateway address is on .251, and I'm plugged in to port eth0 and yet no access to internet.
But, at same time, I have traffic coming in from eth3 via vlan 110, 120 & 130 without any problem accessing internet.

Am I missing out something here?
*
if you put eth4 as DHCP... from where eth4 will get the DHCP? hmm.gif it needs DHCP input.. unless you assign them an IP, then it will gives IP to PC or any devices connected to eth4..
bear1305
post Mar 3 2017, 04:27 PM

New Member
*
Junior Member
34 posts

Joined: Oct 2004
From: Selangor.



QUOTE(wanttotree @ Mar 2 2017, 03:13 PM)
Please post yr config bro.
*
Sorry, newbie here..what's the command to get the config from CLI? blush.gif

12 Pages < 1 2 3 4 5 > » Top
 

Change to:
| Lo-Fi Version
0.0182sec    0.10    6 queries    GZIP Disabled
Time is now: 28th March 2024 - 06:42 PM