[OFFICIAL] Ubiquiti Networks, Home/SOHO/Enterprise Networking
|
|
 Jul 27 2016, 01:35 AM
Return to original view | Post
#1
|
 
Senior Member
975 posts Joined: Sep 2004 From: Setapak   
|
QUOTE(sikentut @ Jul 27 2016, 12:11 AM) Am keen to start using an edge router but am not too sure how to configure it for unifi me too, just curious to configure pppoe+hypptv. configure pppoe vlan, no problem..to configure for both, im still   |
|
|
|
|
|
Jul 29 2016, 09:06 PM
Return to original view | Post
#2
|
|
Senior Member
975 posts Joined: Sep 2004 From: Setapak
|
QUOTE(pandera999 @ Jul 29 2016, 05:06 PM) currently ppoe+happytv is using which device? tm device? last time I configure for a friend once (luckily he don't bother about hypptv). the way I configure that time (about 2 years ago) using CLI QUOTE configure Now I try to figure it out if I wanna both (vlan pppoe+hypptv). i have a basic knowledge to configure few brands like dlink, asus, tplink and mikrotik.set interfaces ethernet eth1 vif 10 pppoe 0 user-id <username> set interfaces ethernet eth1 vif 10 pppoe 0 password <password> commit save |
|
|
Aug 1 2016, 05:03 PM
Return to original view | Post
#3
|
|
Senior Member
975 posts Joined: Sep 2004 From: Setapak
|
QUOTE(pandera999 @ Aug 1 2016, 09:21 AM) currently how do u think they configure for happytv+ppoe? 2 WAN or 2 LAN? most probably 1wan+2lan (in wizard), after that need to add vlan for PPPoE and hypptv. Yup edge OS do have CLI, which most ubnt user used for advance config (there are a lot of video Edge OS CLI). The only way that I can figure it out (let say eth1 from unifi modem and eth2 for hypptv) edge OS CLI? QUOTE configure Bridge may cause performance drop because is using some cpu power. im not sure if bridge will disable pppoe offloadset interfaces ethernet eth1 vif 500 pppoe 0 user-id <username> set interfaces ethernet eth1 vif 500 pppoe 0 password <password> set interfaces bridge br0 set interfaces ethernet eth1 vif 600 bridge-group bridge br0 set interfaces ethernet eth2 vif 600 bridge-group bridge br0 commit save |
|
|
Jun 22 2017, 04:54 AM
Return to original view | IPv6 | Post
#4
|
|
Senior Member
975 posts Joined: Sep 2004 From: Setapak
|
QUOTE(mileage123 @ Jun 21 2017, 11:37 PM) Trying to figure out how set this up while waiting for my units to arrive. But have yet to purchase any UAP AC yet. Dont know much about ubnt, but here is my best answer. For question 1 n 2, UAP AC/UAP AC Pro are access point (much like a switch for LAN). All traffic to the internet is under responsible by a router. Load balance is need to be perform by router (er-8). Not sure your question no.3, each PoE injector (supplied in each UAP) is to powered for each UAP. ER-8 is powered directly to ac plug.Have a few questions : 1. Is it possible to have 2 ISP into 1 UAP AC? Either separated or load balanced will do but I'm keen to know if both will work or not. 2. Do I need 2 ethernet ports like the UAP AC Pro to have both ISP LAN connect to it? 3. If question 2 needs 2 ethernet port UAP AC, is there any flaw or drawbacks connecting 2 PoE Injectors into my ER-8(still curious to know this even 1 injector is enough)? |
|
|
Sep 14 2017, 05:40 AM
Return to original view | IPv6 | Post
#5
|
|
Senior Member
975 posts Joined: Sep 2004 From: Setapak
|
QUOTE(liquid.D @ Aug 31 2017, 01:24 PM) Anyone use 900Mhz CPE NLOS yet (Rocket M9 or Loco M9)? I don't think so that are legal to be use in Malaysia, so far that range of frequency can be used for long range rfid.Hard to find this CPE, mostly 2.4Ghz & 5Ghz available (i might be wrong, i haven't look closely into MCMC/SKMM spectrum plan/resources). |
| Change to: |  0.0600sec
 0.32
 7 queries
 GZIP Disabled
Time is now: 30th November 2025 - 03:21 AM |
Quote