hw much vcore u feed it? has it reach the wall? wats the load temp?
if its high thn u need a better hsf

looking at p00kit's oc results, i was inspired to find out the upper limit of my e6300. But sadly, i kinda hit the wall somewhere before 470 fsb

At 470fsb, i could load windows @ stock vcore, and even run the superPI 1m but it would only last for like 5 seconds in orthos! argghhh.. i've even tried to pump the vcore to 1.4v but still no go.. using ds3 with kvr 667 1 gb (single).
i've tried running the ram at 480 mhz using divider 4:5 (or 5:4) and it works well, which should mean that the ram should work at 470 fsb or is it?

Could it be my psu holding me back? Im using Acbel 450w. The 12v rails looks okay to me..

might be the proc reach the limits already...im not sure also...wat cooling u using? if u dare try pump more vcore

using the thermaltake bigtyp vx only. But the temp is not so bad.. i usually go for this crazy runs when my room is pretty cool (air cond at full blast). Even at 460 FSB, my load is still below 55c.

i guess your right, probably its the proc. I've always thought this baby had potential.. (i could run 430x7 @ 1.25v)

Im pretty sure its fine. THe retention mechanism is not the same as the vx but it would fit into ure 775 socket.

Typoon is same with Typoon vx??
Your Typoon vx did block the RAM slot?

i guess is yr KVR ram that holding U back....coz 470X2= DDR940...which is high for a kvr...

I actually tried running the ram @ ddr940 using a divider. ie having my fsb @ 376 and using a 4:5 divider (2.5 in the ds3 bios setting) to get an effective speed of ddr 940 for my rams). At these settings, i could pass orthos blend and large. Or is running ddr940 on 1:1 different than running 4:5?

wow...430 @ 1.25v is nice

wah..u are so great..see ppl bid u also bid..

bah me jealous, i run 430 lowest at 2.75always mistake 2v actually 1.75.......

This post has been edited by deric88: Jan 15 2007, 11:24 PM

omg
1.75 is high!

hope anyone can help me ere..

since i used orthos as tool to stress my cpu i never encounter this.hop anyone can xplain to me what might hav been wrong..

n FYI i had stress my cpu 4 almost 7 1/2 hours.suddenly this happen n it restart stressing by itself until 19 minutes+

thx



This post has been edited by frank_fusion: Jan 16 2007, 01:50 AM

do a memtest
also check ure transistors on mobo burn or not
kekek

maybe the batch of es u buy from nakata101 got some faulty cpu which it seem so but i dont see other reporting problem from nakata101 bulk for e6600 ES....just my 2 cents

Guys,

Im going to attempt to shift to the Intel side. Hope you guys can give me some pointers.
First, my plan is to get a E6300 and OC to 2.6++Ghz. mainboard GA-965P-DS4 (rev. 2.0). I dont wanna OC that high but wanna seek good tempetature and adaquate speed.

Looking for budgets things here. What type of memory speed and types should I buy.
Is CM iGreen line 560W is adaquate to run my system with 7900GTO/8800GTS?
For a start do I need to get a CPU Cooler?

personaly, i would not get the CM iGreen PSU. i would rather get somethng from Siverstone to powerup my rig.
well, 2.6 is only a 800mhz oc. the stock HSF with a fresh coat of AS5 and u shud be ready to go.

What RAM should i get? I looking for silverstone and enermax but i dunno where can i get silverstone. Also looking at CM hyper TX for cooling.

wei bro ask moderno he got quite a number of silverstone

also i recommend only the zeus series

how much? is it cheaper or more expensive than the liberty?

yeah
a lot more.

it depends what ure running bro.
liberty is awesome but look at the amp railings on the 12v

example my zalman has 4 12vols, each at 16v but the last two 12v more for the pcie cards... so have loads of power for a graphic card.

zeus cooling is way better.
con part is zeus is not modular. but it supports the latest eps mobo
liberty doesnt.

www.modernopc.com

call him later larr..

me support moderno
y?? cause eventhough the price about the same as anywhere else. but
easy leh just call supplier/distributor if u want to check stock.
then call moderno and he will get it. if not ask him to call.
second his place is in subang...easy... hate ly cause a lot of ppl windows shopping
and loads of ppl talking crap that this is good but has no clue about what they are talking about

This post has been edited by cstkl1: Jan 16 2007, 08:22 AM