The Case Fans Thread, Fan Fan Fans
|
|
 Nov 18 2006, 08:12 AM
Return to original view | Post
#1
|
 
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur    
|
actualy there is 14 and 25 cm fans bt nt that ive seen any in malaysia bt performance pcs sell them....
http://www.performance-pcs.com/catalog/ind...ca16f386faf33cf http://www.performance-pcs.com/catalog/ind...index&cPath=327 |
|
|
|
|
|
Nov 18 2006, 10:15 AM
Return to original view | Post
#2
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
yeah saw that too....the cfm should be around 40+ with 30- db
not bad bt evercools best..... or if u can get the yate loons are the best, very silent yet got the cfms..... anyway if u wan best noise to cfm ration best bet is the panaflow series, 120mm, i personallaly own one and bvery happy with it, bt after a while the fans have a small clickking nloise that u can mistakenly think its ur hdd... neway this happens only when u undervolt or over volt. overvolting will make the fan very fast bt only slightly noisier bt will die within a few days, killed my 3 panaflows thuis way on my tripple rad... |
|
|
Nov 20 2006, 08:02 AM
Return to original view | Post
#3
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
actually the vizo fans are not bad, 1) they are extremly controllable,(the whole range 80,92,120) 2) they are quite cheap for their performance, 3) if u set it up the right way these fans can push lots of air with minimal noise. heck i modded a 80mm vizo uv onto my stock hsf, put it to 1300rpm, the gc artic silencer is louder ..... n it still keep my temps alomost the same,~2+ .
|
|
|
Dec 4 2006, 05:20 PM
Return to original view | Post
#4
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
|
|
|
Jul 12 2007, 02:46 PM
Return to original view | Post
#5
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
yeah agree with sniper, get teh folowing recomadations by me and i can guess many of us here... yateloon, nmb, scyhte, minibee ( i have 2 and its dam silent and good airflow, but freeking expensive) ,adda, papast, xinrulian , jmc da tech, san ace, sharkoon, nidec and last but not least my favorite fan is panaflow
|
|
|
Dec 28 2007, 07:09 PM
Return to original view | Post
#6
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
QUOTE(Doom @ Dec 28 2007, 07:06 PM) @irangan dont bother with silentx... saw a technical review of it.. airflow is shit...From your opinion which one is more silent ?? SilentX or Noctua ... since u got the experience with both ..  noctua is ok.. minibea is ok.. sflex also ok... but if budget tight.. u can always get the original YAteloon... preety good quality |
|
|
|
|
|
Dec 29 2007, 09:29 AM
Return to original view | Post
#7
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
QUOTE(irangan @ Dec 29 2007, 01:18 AM) Like stated by lolhalol, SilentX is a con stuff and its dont perform as its stated. Conclusion, it is a crappy fan.. The creator got banned in several forum because he self promoted the fan by posing as customer. hehe like you lah.... So as for your question, of course Noctua is more silent  Ya.. it is a sucky fan. No where near to those really 'branded' fan. FM121 and FM122 are good but abit too noisy (weak in dba / cfm ratio). Meanswhile, FM123 is total crap according to most user feedback that I read. It is said that its cfm just cant justify the noise its produced. You cant whine much when it is one of those few 'branded' fan that can easily found in Malaysia. But if you have other option like S-Flex, Minibea and Panaflo, you wont even look at Silverstone fans. Haha. kena my poison hehehehe....QUOTE(Doom @ Dec 29 2007, 03:44 AM) hmmm .. .. looks like Noctua still my best choice .... seriously minibea is the way to go.. u will not regret...the medium range is the best if u dont like to control ur fans...I'm favor of silent more than performance ... as long as it's not below 35cfm on full spin .. it's fine with me ... So far I hardly feel any strong advantage with high CFM fan ... it brings down an additional 2~2 degree but the noise increment just too much ... QUOTE(E-J@1 @ Dec 29 2007, 04:14 AM) yup, same here hehe minibea brother.. beware once u touch.. u will not go back... like me , irangan , cabelsguy alsohave to find the sweet spot for it where the increment on the CFM is useless (doesn't justify the noise increment)  want full blast = 70cfm, yet ur heatsink has its limit sinking the heat  in the end, u'll get a noisy setup just for the sake of 1-2 degree difference than the sweet spot noise or cfm  |
|
|
Dec 30 2007, 12:07 AM
Return to original view | Post
#8
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
http://www.performance-pcs.com/catalog/ind...24737581f178c11
here you go mate.. beware once u see u will buy.. once u buy.. u will want alot fo it..lol |
|
|
Dec 30 2007, 09:59 AM
Return to original view | Post
#9
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
QUOTE(clayclws @ Dec 30 2007, 03:16 AM) It's made by NMB...why not just get 1 from AllnGap? its made by nmb doesnt mean its the same....he bearings are totaly different.. and the blade design is too..... |
|
|
Jan 5 2008, 07:27 PM
Return to original view | Post
#10
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
QUOTE(clayclws @ Jan 3 2008, 02:46 PM) Over at Jalan Pasar...apart from NMB, any other fans that are worth mentioning there? Delta is a no-no... umm nakamichi ( bet u never heard of this  )? jmc datech ? panaflow ? sunon ? everflow? |
|
|
Jan 8 2008, 10:20 AM
Return to original view | Post
#11
|
|
Senior Member
1,823 posts Joined: Mar 2006 From: Kuala Lumpur
|
QUOTE(clayclws @ Jan 8 2008, 10:53 AM) Can't find any Panaflo or Everflow over at Jalan Pasar. Found NMB, Nakamichi, JMC/Da Tech, Sunon, lots and lots of Seada and Delta, San Ace/Sanyo Denki, and many really weird brands. Best one I've tested so far seems to be NMB. Silent but blows my hair real well ahh panaflow and everflow need to dig abit yeah all those fans will work for u lah.. alot of them are meant for heavy machinery that needs cooling... |
|
Topic ClosedOptions
|
| Change to: |  0.0398sec
 0.68
 7 queries
 GZIP Disabled
Time is now: 3rd December 2025 - 01:06 PM |
Quote