need help ere..
DFI LP CFX3200 + TEAM XTREEM HERMES DDR PC 4800 TCCD

compatible???

at last...

take a look here...

Genie BIOS Settings:

FSB Bus Frequency............................. - 300
LDT/FSB Frequency Ratio....................... - 4.0
CPU/FSB Frequency Ratio....................... - 9.0
RD580 HT PLL Speed............................ - High Speed
HT Bus MMOS Drive Strength.................... - 05
HT Bus PMOS Drive Strength.................... - 05
HT Bus Receiever Impedance.................... - 05
CPU HT Bus Drive Strength..................... - Normal

CPU VID Control............................... - Auto
CPU VID Special Control....................... - dun remember but set till get 1.6v
DRAM Voltage Control.......................... - 2.80v
SB PCIE Voltage............................... - 1.80v
NB Analog Voltage............................. - 1.34v
LDT Bus Voltage............................... - 1.34v
NB Core Voltage............................... - 1.34v


DRAM Configuration Settings:

DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 3.0 Bus Clocks
RAS# to CAS# delay (Trcd)..................... - 04 Bus Clocks
Min RAS# active time (Tras)................... - 08 Bus Clocks
Row precharge time (Trp)...................... - 04 Bus Clocks
Row Cycle time (Trc).......................... - 10 Bus Clocks
Row refresh cyc time (Trfc)................... - 16 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 03 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 03 Bus Clocks
Refresh Period (Tref)......................... - 1560 Cycles
DRAM Bank Interleave.......................... - Enabled
Errata 94 Enhancement......................... - Disable
Errata 123 Enhancement........................ - Auto
Odd Divisor Correct........................... - Disable

DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
DRAM Drive Strength........................... - Level 3
DRAM Data Drive Strength...................... - Level 1
DIMM 1/3 Clock Timing Skew.................... - Auto
DIMM 2/4 Clock Timing Skew.................... - Delay 450
Max Async Latency............................. - 8.0 ns
Read Preamble Time............................ - 5.5 ns
IdleCycle Limit............................... - 64 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 4 x
Burst Length.................................. - 4 Bursts

got to 2.7ghz with these settings...

if it's not compatible, you wont even be able to boot it. it's that simple.

This post has been edited by soulfly: Dec 24 2006, 11:56 AM

update...
it's very unstable...
right after i quit playing company of heroes for 3 hours then kaput.. (restart laa not blow)

maybe you can try lowering down your

LDT/FSB Frequency Ratio....................... - 4.0 to 1.0 or 2.0?

i test running memtest @ 250mhz @ 2.5ghz got no error... 25 pass

can boot into windows but then blue screen....

ok then...
is your 2.8vDIMM is really 2.8vDIMM? well mine read @2.87vDIMM (2.8V) while 1.376vCORE (Start-up).

to run @ ddr600 u gotto fine tune it, last time i own this ram before, takes me lotsa times to fine tune it...

the vdimm is comfirm @ 2.8v.. reading @ 2.83v

if people using ddr600 with any nf4 mobo i think got no problem... a fren of mine once use this ram got no problem...
try using it on DFI LP CFX3200-DR/G...
u'll will start to cry when u want to set the dram setting...
u have to set each setting properly to get a good result...
i'm alreadi out of idea.....

Its correct, 250mhz u use 4x. But if u want it to run at 300mhz u need to use 3x multi.

well, let me recall back what OPB said before. (not applied to nf4 non expert or venus)

1. Don't set MAL and RP under bios. You have to set AUTO.
2. IdleCycle Limit - set to auto under bios to boost MAL tighter.
3. If go higher fsb, then DS can go with 1. DDS sometimes can be tricky, if you have very strong ram, try 3 first, but always from auto, then if safe, go 2 then go 3, normally 2 is just perfect for average users.

or u can try to lower down the voltage
for my case when the voltage set over 2.6v
then will blue screen some time
and try ds 8 dds 3 1st and start tunning from 250 fsb to 300fsb

25pass is nothing, try atleast 100 loops.

agree, most if d tccd (espcially older batch) don't like high voltage, 2.5~2.7v is d best for my case.

huh.....for a while now casperito cannot on9.....got some network problem in his house.....then we just have to wait....