Outline ·
[ Standard ] ·
Linear+
Coolermaster GeminII, discuss anything this cooler here
|
^666^
|
 Jun 8 2007, 05:09 AM
|
|
i just got my cooller master gemin II from robyn com imbi for only at RM130!!!!! the result Brisbane 3600++ stock speed - 19 idle 23 max load  Brisbane 3600++ 2.9ghz 1.425vcore - 30 idle 38 max load pair it with 2 lianli stock case fans....spining around 1800rpm  Tips & tricks for the gemin II-makesure the bracket of the cooller its installed properly balance u can get the diff if u installed it properly. -put a little bit more thermal paste from usual as the base is quite big and its hard to balance. -Adjust the fans corectly.i just adjust it according to the temp reader the lower its the best!! -This cooler its the best cooler among other cooler tat ive used if u adjust the cooller properly This post has been edited by ^666^: Jun 8 2007, 05:11 AM |
|
|
|
|
|
^666^
|
Jun 10 2007, 06:30 AM
|
|
|
no air cond!!!!...only ceiling fan.... i think my temp is normal coz if use stock cooler on stocksetting is 35-39...i think tats normal...... this is the proof.... this is the setting i used for tight timings team value on 7++mhz 4-4-4-12...running 2.4ghz on 1.45...can run 2.9 on 1.45 also but timing must loose 6-6-6-15...temp slightly higher abit ony..... This post has been edited by ^666^: Jun 10 2007, 08:06 AM Attached thumbnail(s)
|
|
|
|
|
|
^666^
|
Jun 10 2007, 11:08 AM
|
|
|
ok updated using prime....... Attached thumbnail(s)
|
|
|
|
|
|
^666^
|
Jun 10 2007, 08:36 PM
|
|
|
Where can i get core temp?....i always use the mobo bundled 1...updated with orthos...
|
|
|
|
|
|
^666^
|
Jun 10 2007, 08:55 PM
|
|
|
ok...update with core temp.... Attached thumbnail(s)
|
|
|
|
|
|
^666^
|
Jun 10 2007, 09:25 PM
|
|
|
thumbs for gemin II...
|
|
|
|
|
|
^666^
|
Jun 10 2007, 09:51 PM
|
|
|
nope...it will not block.....if ure using the std...
|
|
|
|
|
|
^666^
|
Jun 10 2007, 11:12 PM
|
|
|
blow in of coz....u need higher rpm to make it perform better....at least 1500rpm...
|
|
|
|
|
|
^666^
|
Jun 11 2007, 08:18 AM
|
|
|
QUOTE HI, i'm using Gigabyte 965P-DS3 v3.3 mobo,
it fits well!! hoho.. just a little bit problem where by u need to a slim hand to plug molex connectors of your PSU (am i call it right tongue.gif) onto your mobo.
And to kerryking, yup it fit well in my casing. I'm using normal ICute ATX middle casing. But now i can't install 2x 80mm fans at the back of my casing. The fan bracket of Gemin II (please note that it's Gemin II , but not Gemini II) dominates whole of the upper space of my casing, and i have to remove my 2 80mm fans, and this makes my core temp maintain at 45 to 48 degree C. sad.gif
This is not Gemin II's fault but mine as when i bought my casing i never thought that i would fix this pretty monster in my casing. tongue.gif Planning to change casing, anyone can suggest me? I want a aluminum silver casing with windowed panel, and my budget is around Rm300-350. Planned to get Ah-lian PC-007F, is it good and can fix this monster?
And to ^666^, the 120mm fans that u installed on Gemin II, are they blow in or out?
Last words to end this: I love Gemin II rclxms.gif rclxms.gif rclxms.gif Actually ur prob isnt the case prob.....is mobo prob... ds3 proc location near the backplate...if u change case oso cannot put fan at the back...  so my sugestion change mobo... |
|
|
|
|
|
^666^
|
Jun 11 2007, 08:03 PM
|
|
|
QUOTE Err...
If wanna change mobo,
What mobo would u recommend? DFI? hehe... yup...my recomendations for mobo Dfi,Abit quad GT, DS3R, or The Fatality FP-IN9 SLI...tat's the best board ive tested...but u try to search the most long gaps between proc and the back plate.. |
|
|
|
|
|
^666^
|
Jun 12 2007, 02:50 AM
|
|
|
can fit laaa....am2 no prob i think coz....most of c2d mobo have the loc prob....
im using biostar T-force 570sli....no prob...
|
|
|
|
|
|
^666^
|
Jun 19 2007, 11:29 AM
|
|
|
bro u silap pasang laa idle should be 20+ ony...
|
|
|
|
|
|
^666^
|
Jun 23 2007, 07:53 AM
|
|
|
mine aaa idle at 21c ony lol....if no ocing done...if oc 36c....
|
|
|
|
|
|
^666^
|
Jun 26 2007, 04:11 PM
|
|
|
actually gemin do have issues on the 775 coz they dont include the back plate for the heatsink for 775.....the back plate only can use for am2 and 939...
so the weight of the hsf+2 12cm fan cannot stand by the mobo with no hsf back plate attach cousing to no balanced presure towards the proc....
Resulting a not very good contact bettween proc and heatsink base....
So this coller is great on AMD platform....
My idle on stock 1.9 is 25~
Idle on 1.3v stock vcore 25~
Idle on 1.45 1.425 vcore 32~
So its actually the best coller for amd rite now.....ive tested HR01-Ultra 90-BT VX-G-power
This Is still The Best!!
This post has been edited by ^666^: Jun 27 2007, 01:38 AM
|
|
|
|
|
Quote
0.0271sec
0.82
7 queries
GZIP Disabled