How long used before this? Is there any error codes thrown?

Authorised give you 2nd hand spare part?

If 3rd party, I would believe.

Hi everyone,
Im thinking to buy panasonic inverter aircon,
should i go for new aero series or sky series?
Anyone used sky series?is it effective as it ad?
Thanks in advance 😊

My aircon service guy said panasonic non-inverter is good, but inverter type has more problems. Just to let u know

Planning to get SHARP AHXP13UXD aircon.

Anyone using this model? any feedback?



SPECS:
EER 13.2
Nett Weight 9 kg (Indoor) / 20kg (outdoor)
ECO Mode Yes
Dual Drain Setting Yes
Dimension (WxHxD)(mm) - Indoor 856 x 290 x 244
Baby Sleep Mode Yes
High-Density Plasmacluster Ions Yes
12-Hour ON/OFF Timer Yes
Running Current - Cool (A) 5.0
Best Sleep Mode Yes
Quiet Operation Yes
4-Way Auto Air Swing Yes
Super Jet Yes
Series Wall Mounted Split Air Conditioner
Airflow Volume - Cool / Indoor 11.5
14m Long Airflow Yes
Refrigerant R32
Horsepower 1.5
Capacity 12,500 (2,860 - 15,000) BTU/h
Inverter Controlled Operation Yes
Dimension (WxHxD)(mm) - Outdoor 598 x 495 x 265
Self Cleaning Function Yes
Power Input - Cool (W) 695
Auto Swing Louver Yes
Power Supply 220-240-1∅-50
Pipe Diameter - Gas Side (Inch) 3/8
Dragonfly Fan Yes
Awakening Function Yes
Voltage Range (V) 198-264
Pipe Diameter - Liquid Side 1/4
Auto Operation Mode Yes
Lock-On Sensor Yes

more in on brochure =>  J_Tech_Inverter_Brochure.pdf ( 3.76mb ) Number of downloads: 31

Hi all, looking for help. My room old aircond not cold anymore, but still function well. Any contact for aircond repair and how much to repair ya? Please help, all sifu around here~ thanks

Where the hell you get this window type aircon? How many HP?

Just call back the York SC.

u never heard what is "window unit"?

probably refrigerant leak.
So have to check for leakage and top up gas.

It depends if it's easy to isolate the zones such that each one can cool it down without being overtaxed. I'll prefer this approach too. If you think it might overtax then go for 1.5hp at the crucial one like bedroom. One easy way to partition is to use thick curtains.

Three things to consider:
1. Piping insulation. Individually sleeved per pipe. Use Inaba Denko's (JP) or Smartco's (KR) Paircoil. Sets you back a bit but guarantee will not develop leaks so long as installed correctly. Use 0.8" thickness for R410a which is also compatible with R32. The requirement is to guarantee AC runs at its rated power without which (all in one jacket/sleeve), the mixture causes the compressor to overwork (higher electricity consumption than rated) which can potentially damage the indoor unit cooling fins esp if the piping runs are in excess of 3m. This is evident when there's freezing on the AC cooling fins due to this caused by the compressor overworking to compensate for inadequate cooling capacity. You'll know when you hear the sudden tak tak sound of ice forming and bending the fins. Leaky pipes can also cause this over time. Quite common in old AC but not sure perhaps they've mitigated this now.

2. Piping size - it's ok to oversize such that in future, if you need to upsize, there's no need to hack and repipe. Bear in mind the gas / return / hot pipe should be equal or larger, never smaller than that of that AC model used. For example, 1.5HP on a 2HP pipe or 2HP on a 2.5/3HP pipe. If experience bears out that a 1HP or 1.5HP cooling is insufficient, you can in future swap that out and get a 2HP but without changing pipes.

3. Long air throw. If relying on a single, bear in mind that certain AC have what's called long throw feature like the Sharp inverter (14m even on a 1HP) or a Mitsubishi Electric Mr Slim. The Sharp has a ceiling throw mode for gentler cooling too.

Hi all, looking for help. My room old aircond not cold anymore, but still function well. Any contact for aircond repair and how much to repair ya? Please help, all sifu around here~ thanks

Hi, I would like to buy Mitsubishi Electric Air Cond but noted that it has 3 types of refrigerants:-
1). R22
2). R410
3). R32

Which one should I go for in term of repairing. servicing (easy to get the spare parts), stableness(no easy to break down) and quietness(the compressor not running noisily)?

Hi, I would like to buy Mitsubishi Electric Air Cond but noted that it has 3 types of refrigerants:-
1). R22
2). R410
3). R32

Which one should I go for in term of repairing. servicing (easy to get the spare parts), stableness(no easy to break down) and quietness(the compressor not running noisily)?