Talking about Mec Mods. My friend borrow me his with only the wording "FxxK YOU" on it. I never own one before, he is newbie too, told me he dunno how to insert the cotton. I saw on YouTube on how to replace and inserted a facialcotton pad (not Kotex for sure), and yes I know it's not organic but just want to try. Man, the cloud it produce is even thicker than Atlantis on 30W with a short lung hit. Few hits and my whole room is so vapory!

I was recommended here with Derringer RDA, I know it can use on regulated mods but what true Mec Mod is good? Is the Praxis Mod good with it? I do see one sort of like iron man with spikes (stainless steel and copper or bronze color). Which one is better? I m just a month newbie too.

I don't agree with that. I was into RC car and Heli 7years back, so I do know a little about batteries. High discharge is meaning that it can discharge at a higher rate safely without over exhausting the batteries. It will just remain at the same temperature or slightly warm, and will not explode or melt like those lower discharge rate ones do. So I don't think it hs anything to do with harmful effects on ecig.

no one know the solution??

I dont really know much about which is good n which is no good for mech mods cause their theory is very simple..
But from what I learned through a year of vaping, if you're looking for a good mech mod, look for mods that usses copper pins..

I think those batts are made for laptop batts..cause a friend of mine did took out his laptop batts n tear it open, n what we found inside are those 18650 batts..they are 6 of em inside those casings...

I think what u could do is go n buy another bottle of em bad ass juice n mix em together with the one u r having, so u could reduce the mint...

Buy another bottle of same juice without menthol and mix together?

Laju nya tered.. Tak terfollow

This post has been edited by wan.ridzuan: Mar 27 2015, 08:16 PM

guys which 1 is better,pls comment

Those batteries are usually factory / distributor direct & they are usually meant for laptop battery cell rebuilds. Yes they can also be used for other purposes, including vaping. The info of the battery is usually available on their datasheet. Since we don't have datasheet, the closest alternative you can think of is to Google the model number. Open a few results can make sure the info is identical. Eg. ''Samsung INR18650-25R spec'' Idk why many Malaysian vape stores and online store fail to provide full info.

Anyways, you can use this link too. http://www.steam-engine.org/batt.asp

You need to know the name and model number of the battery first.
Then, click battery preset & select your battery.
Don't touch anything else.
The amp limit, capacity, nominal voltage & c-rating is there

--------

On another note, that link (under 'coil wrapping' tab) allows you to build a coil without an ohm meter.
I've tried it, as long as you know how it works & what every figure means, you can build a coil within .2ohm of your target.
But for safety, always use a resistance meter to check.

You must use 'coil wrapping' together with 'battery drain'. It's easier if you both open each in a separate tab on your browser
You need to get your battery wattage based on your desired resistance at different voltages.
Then input the wattage in 'heat flux' under coil wrapping tab. For example, my batt as mentioned above @ 0.5ohm. build will give you about 35W at fully charge 4.2v, it goes down to 20+W at 3.5v...

Hence, now go to coil wrapping. After selecting your wire, gauge, your coil setup, resistance and other figures...
Put that watt in 'heat flux' and check the mW/mm² figure between min & max wattage is between 220 - 310 for (generally) thick clouds (for mech mod). If you cannot achieve that, you need to adjust the resistance of your build etc. For every change in resistance, go back to the battery tab and get the new range of wattage. Redo the heat flux section.

For VV/VW mod, you dont really need to worry about this as you can adjust the volt/wattage to your liking on your mod, but if you are recoiling, it's a good idea to know how hot it gets at a specific watt/volt setting.

Under batt drain, you can also check how much 'safety headroom' you have at a specific ohm & voltage. >55% headroom is recommended. Really good shit.

Again, this is for the advanced & precise fellas, dont mess around if you are sloppy or dont know what you are doing, things can go boom easily.

These link should be included at the 1st post for DIY fellas:
http://www.steam-engine.org/coil.asp
http://www.steam-engine.org/batt.asp

One of my prev single coil build


This post has been edited by andrew9292: Mar 27 2015, 09:21 PM

I dunno man. Kanger own website listed FT as one of those that sells subtank clone. Check it out http://kangertech.com/?copycat.html

Mech mod for lifereeeeee

Mini 4 me of course..
My suggestion is go n get it from our local seller, cause price is much cheaper n u dont have 2 wait a month to get your stuff..

If not mistaken FT do mention if their subtank is either authentic or clone..

becauae they build for other purpose n not for lose selling ......

is it just me or depends on each user?

i think i like the aftertaste and vapor production from Atlantis better then Kanger Subtank Nano.

Anyone else feels the same?

depends on what mod you're using for it. subtank plus is 25mm wide, while mini is only 22mm wide.

yes. got liquid really sucks in my subtank mini, but tasted heaven in my lil' bros' atlantis

how to get the best out of mech mod ? Freshly baked batteries with short cap dripper tanks (eg: Deringger INB4 ERA, hornet, IGO-L and so on) with soaked cotton/wick, you will enjoy fireworks on your lips/mouth.
full blast on 3.7~4.2 V will set you back heavenly.

downside is when battery starts to get low, your vape starts to produce less clouds.

First mech mod = K100 (legend) ! that time no money to buy Nzonic, private, PINOY and stuff. Mampu tengok only.

So far still maintaining my chi you mod. One of everlasting mod IMO

Mech mod is fun, you control your clouds by recoiling

cheers

This post has been edited by efili: Mar 27 2015, 10:48 PM

i've been watching couple of review on this i-stick 50w, n most of them said this is very2 good mod.. but not in msia yet. i'll be buy this next month
tunggu sampai price war baru beli.. haha


Attached thumbnail(s)

I know right My last post was about 4-5 page back... Meriah malam ni

Time to embrace the future dude

New inclusion to the family ....

fastek kan hadoo

Vaporflask ka?