Outline ·
[ Standard ] ·
Linear+
AMD K8 Family Overclocking (754/939/940/AM2/1207), General discussions and newbies' guide
|
realone
|
 Jan 1 2006, 10:33 AM
|
|
my pc spec
amd 64 3000+
KVR 512mb ddr400 x2 (double sided)
winfast 6600gt
msi k8n neo4-f mobo
ok, the problem is that when i run on 1:1 divider(250 fsb,250x9=2.25Ghz,,3X htt) PASS;
but when i wanna test how high my proc can go ,so i have to use divider,
5:6 divider(166mhz ram) even cannot pass 240 fsb(240x9).. FAIL.
what should i do??pls help
This post has been edited by realone: Jan 3 2006, 07:42 PM
|
|
|
|
|
|
realone
|
Jan 1 2006, 11:33 AM
|
|
|
QUOTE(low yat 82 @ Jan 1 2006, 11:18 AM) act.. ualrady got thread to ask... http://forum.lowyat.net/index.php?showtopic=139453anyway.. ermm bout ur prob.. u dun tell us wat test was pass  r u sure u r using 166mhz divider ? check it at cpu-z... and print screen it here and also other related info... btw u using 1T timing or 2T ? ok,run on 1t |
|
|
|
|
|
realone
|
Jan 1 2006, 01:11 PM
|
|
|
i think is my ram problem..before i upgrade to 512x2,,,,256 x2 is running fine and can reach 300mhz fsb.......
|
|
|
|
|
|
realone
|
Jan 2 2006, 12:26 AM
|
|
|
QUOTE(wtm0325 @ Jan 1 2006, 11:55 PM) higher LDT wont help, try to use 1 stick ram n c ok, i will try later |
|
|
|
|
|
realone
|
Jan 2 2006, 12:58 AM
|
|
|
QUOTE(realone @ Jan 2 2006, 12:26 AM) ok, thr result is ,,,fail...same no post if i try use any divider... |
|
|
|
|
|
realone
|
Jan 2 2006, 01:19 AM
|
|
|
yeah, confirm is ram problem.
|
|
|
|
|
|
realone
|
Jan 3 2006, 07:38 PM
|
|
|
 my ram hitting limit liow...have to change ram since it cannot rn on any divider ....end up no post,,,run on 1:1 is fine...run memtest,,stable.. 3d mark 2005 3d mark 2003cpu-zi'm looking secondhand gskill 3200 fx..512x2 ddr400 This post has been edited by realone: Jan 3 2006, 08:08 PM |
|
|
|
|
|
realone
|
Jan 3 2006, 07:41 PM
|
|
|
need help to improve my 3d score and overall system...
|
|
|
|
|
|
realone
|
Jan 3 2006, 08:04 PM
|
|
|
QUOTE(e-jump @ Jan 3 2006, 07:58 PM) dude, it may also be ur bad proc memory controller altho i didnt suffer prob luke urs, but my 133 devider is useless n 166 devider can only hold the ram till ddr500 but u didnt mention what test fails.. beside bad ram n bad mem. ctrl'r, psu also may cause the prob as i state above ,before that when i run 256x2 kingston ddr400....its run fine and can use any divider,,,but after upgrade to 512 x2 ,,,,can't even run any divider,,, |
|
|
|
|
|
realone
|
Jan 3 2006, 08:05 PM
|
|
|
so, its confirm ram problem,,,perhaps it dun like divider,, hehe
This post has been edited by realone: Jan 3 2006, 08:06 PM
|
|
|
|
|
|
realone
|
Jan 4 2006, 10:23 PM
|
|
|
QUOTE(antonio_zth @ Jan 4 2006, 02:21 PM) newer version kingston value rams are unable to get you 240+ and above...but since you can run at 240 why not u try setting such as 2T 3-4-4-10 and use divider to drop ur ram to either 100 or 133mhz and then push again...just to see if your proc is limitating ur overclock.... ok, i will try |
|
|
|
|
|
realone
|
Jan 6 2006, 11:37 PM
|
|
|
QUOTE(antonio_zth @ Jan 4 2006, 02:21 PM) newer version kingston value rams are unable to get you 240+ and above...but since you can run at 240 why not u try setting such as 2T 3-4-4-10 and use divider to drop ur ram to either 100 or 133mhz and then push again...just to see if your proc is limitating ur overclock.... no post ...  |
|
|
|
|
Quote
0.0370sec
0.50
7 queries
GZIP Disabled