CnQ must be disabled if u run rams on devider anything other than 1:1 [200:200]
no problemo if 1:1

This post has been edited by e-jump: Apr 7 2006, 02:10 PM

any idea how 2 push higher then 2.6GHz? my target is 2.8GHz and above!

2.4GHz
HTT = 267
Multiplier = x9
CPU Voltage = 1.4375v
Hyper Transport = 4x
Super PI (1M): http://i24.photobucket.com/albums/c17/oymy...ase/superpi.jpg
CPU-Z: http://i24.photobucket.com/albums/c17/oymy...0Database/2.png

2.6GHz
HTT = 289
Multiplier = x9
CPU Voltage = 1.500v
Hyper Transport = 4x
Super PI (1M): http://i24.photobucket.com/albums/c17/oymy...e/superpi26.jpg
CPU-Z: http://i24.photobucket.com/albums/c17/oymy...tabase/2600.png

memory setting:
333MHz
3-4-4-8 (2T)

This post has been edited by gmail: Apr 8 2006, 10:43 PM

Both of your links are not working. Btw, change to a better cooler/hsf if heat is unbearable. If heat is not the problem, then try ramping up the vcore a bit higher.

This post has been edited by PCcrazy: Apr 8 2006, 09:19 PM

link posted again! i push the vcore still cannot!

hehhe..it might be already at the limit lor

4*289 is alreaady exceed 1000 leh...

try 3x instead...

yeahh..ur Hyper Transport cannot over 1000 lor..

Hmm, nicely spotted. Didn't pay much attention to that one but it's crucially important that you don't break this rule. Stick to it to achieve greater stability and overclock.

i tried 1,2,3,4,5 and it dosen't affect the performance of the rig. so i put it to 2. no problems so far. dividers, a64 drivers all in. cool and quiet disabled.

my rig
amd64 754 2800 (2.4ghz)
mobo abit nf3
ram ddr400 1gb ct-d43
gc ati 9600xt little oc

so my timing:
3-4-4-10
333 n divider is 3
9 is max multiplier in my mobo
9 X 267 = 2.4ghz

temp:
idle system 35 n cpu 37c
full load sys. 42 n cpu 45c-48c

i can go oc to 2.5ghz but to scared if it will burn huhuhu....

si any suggestion to improve my oc..

what ur vcore? dare it will burn? ..are u using stock cooler?

noop
im using zalman 7000
so it is to hot..
but seems to be standards cause thats sc754 n nforce3
and my command rate is 1T

cpu 1.6v stable
ram volt 2.8v

my OC results, but then in BIOS i have the FSB at 302!!! darn bios might be corrupted. sheesh.

nice clock there, nice to see d chip + mobo works well w/ 140 divider (if i'm not mistaken)...

woot, new version of sp2004...

huh? which divider 140? LOL

ram is at 2/1.33 divider, rams all maxing out already....
and just completed 15++ hours of prime, so this is the most rock stable setting so far, but not the highest

i'm hittin d wall w/ my ram too. sometimes lower dividers like 150, 140 wun work well (atleast in my case). no matter how loose d timin is i just can't get 'em prime stable...

2/1.33??? lazy to do d maths...

so..this is right time to get new HP ram la

that's 133 la
2/1.33 = 200/133 (HTT / RAM speed)

too lazy...

1 q to ask u guys, if say memtest stable (dos ofcoz) but failed in prime within a minute, wat u guys will do usually...

i'm havin hard time to prime-stable my ram @ 245MHz...

Reformat HDD?