If no problem tak payah laa. 

Don't need gatal gatal update. One of the forumers, hasn't update since his gaga left the factory, ok je.

Only update I did was the update so solve semput issue during idle, that's it. 

  thanks for the advice !

btw just curious, how to know whether or not its the latest firmware? haha. 

Semput I don't really like too, really annoying especially for manual drivers, the compressor kicks in when you about to start to move the car, the rpm drop is quite significant. Now not so often lo. Use better fuel perhaps? 

Anyway guys, the front intake grill can modify to mesh wan ah? Or it is integrated to the bumper? Kena change whole thing ke 

Mine is from taiwan. Some rims are replica but not too bad. From my opinion na. Else u can get advanti which is lighter and beiter compare to taiwan and cheaper compare to ori. Is depend on ur budget as well.

Stock rims gooding. 

Stock rims with ur "side skirt" look weird too. 

haha...i know that feeling 

i thought u pasang oledi?
Adjustable. 

6.5J et35 more easy to find but if u r on stock height then u won't sagat. I DIY roll mine only at the rear just in case sagat but before I roll also never sagat unless those really big drop wavy road. I'm also on adjustable 2 fingers at rear and 3 fingers front. So far I use on track day and time attack no problem. No touching of fender or anything

Now I am using lo. Stock height wont sagat la. 

sagat la... 

Mati mati nak rota ah brader, bbs replica pun nampak cantek tu on sagas.
Or kasi all one line je lo, kasi simple. All white fonts gao tim, dont want two lines nie hehehee. But macam mightycarmods punye fonts you cant do ah, simple & nice hehee.

        kena Maxwell6635 virus?

nothing wrong with HU.... its the antenna... memang lemah longlai from factory. lol

IIRC, yup..but it could be the plug and could be other things also. Just my opinion
Actually, this problem I think maybe not just due to the plug type cause I have saw a few cases at SC here the COP rubber broke also when the proton tech change the plug for some Persona and gaga and owners was furious when they were ask to pay for it. I believe regardless of what plug you use there will be heat and the place that hold our COP rubber boot is made of metal and the heat transfers directly to the rubber boot and the rubber boot is a really tight seal with the metal tubing. After my initial damage I have apply some high temp rubber grease meant to be used for brake caliper o ring around the rubber boot and the metal tube. This hopefully can solve the problem of the boot sticking to the metal tube overtime.

Also try not to overtighten the COP too much as it will force the rubber boot to go in much deeper and this makes thinking it out even more difficult. Just tighten bit that much is enough.

I've already ordered a set of Ignite Rev from TM Works Japan to replace the plastic rubber bottom plug of the COP. TM Works Japan know the rubber boot sticking problem so they made some enhancement to their rubber boot line up for Campro COP. Hopefully when I get these babies in.  I will be able try them out to see if they are easier to remove after installed. Price of these is around MYR450-500 depending on the conversion rate. Which to me is a good price because I know TM Works products that sells here are much higher due to the import taxes and such.
Image is for reference, actual product for the Campro I will take pic and post it here once I got them.


Above is just my opinion and idea it could be wrong or could be right.

bulk lai...hehe

Tried a tank of RON97. Mileage same, butt dyno same...so RON97 in Saga is waste gas only.

Yes especially when you tarak pakei akon in selow trafik.

i not sure about your car mia punya vibration. our aircond powderful yo. which part vibrate? steering? whole car?
go see unker david this flyday to check.

Bai VIOS Vios no such issue