PROTON SAGA BLM, FL & FLX Thread V64, Buy Hiriz better.
|
|
 Sep 8 2014, 09:48 AM
Return to original view | Post
#1
|
 
Junior Member
83 posts Joined: May 2011  
|
QUOTE(dares @ Sep 8 2014, 01:43 AM) I've given up learning left foot braking liao its good for FF car    but need to drive the car to really far to use that, lolnow i can drive auto car with left and right foot  |
|
|
|
|
|
Sep 8 2014, 10:00 AM
Return to original view | Post
#2
|
|
Junior Member
83 posts Joined: May 2011
|
QUOTE(dares @ Sep 8 2014, 09:54 AM) the bolded part tak paham full throttle corner, then tap a bit bit to reduce under, normally if tap d will be slower, i don't really know how to explain, but normally i don't use, except rawang to gohtong 2 lane section start, i think quaza to recorded that about 4:4x on ward i think   u see my car tail lamp blink a few times |
|
|
Sep 8 2014, 12:13 PM
Return to original view | Post
#3
|
|
Junior Member
83 posts Joined: May 2011
|
QUOTE(dares @ Sep 8 2014, 11:24 AM) Got ASC ma....just WOT through the corner asc u need ask Quazacolt to fully utilize, some corner like the temple corner i close asc to reduce power loss, cause that corner if asc kick in my car like turtle d   QUOTE(dares @ Sep 8 2014, 11:37 AM) Satria Neo thread member selling wahhh leng ye this one rcs damper , lsd http://www.mudah.my/Proton+Satria+Neo+M+CP...10-29595259.htm quality mods siap ngan LSD  davidke20 titanrev nzh0920 |
|
|
Sep 8 2014, 12:44 PM
Return to original view | Post
#4
|
|
Junior Member
83 posts Joined: May 2011
|
QUOTE(dares @ Sep 8 2014, 12:32 PM) Bulk bulk bulk got , saving money for it.soulless car no aftermarket LSD ka? cusco clutch type and quaife torsen type 4k to 4.5k |
|
|
Sep 8 2014, 12:52 PM
Return to original view | Post
#5
|
|
Junior Member
83 posts Joined: May 2011
|
QUOTE(dares @ Sep 8 2014, 12:50 PM) Brand new? OK ma yup brand new, but need add bearing those thing, abour also donno how much i think close to 6k  |
|
|
Oct 10 2014, 12:46 AM
Return to original view | Post
#6
|
|
Junior Member
83 posts Joined: May 2011
|
QUOTE(TitanRev @ Oct 9 2014, 07:22 PM) n3w kenjilew davidke20 wah bro, your gear knob looks damn nice and solid Guys you gearknob is ready. Sorry for the long wait. The knob length measures at 100mm just nice to grab with whole palm and CNC out from a solid piece of ALU. Diameter is at 30mm Note: just before you screw onto the gear stick try use some old cloth to clean out the threaded hole might have some fine debris or metal shavings inside and would causes a bit of difficulty when trying to screw on.     |
|
|
Oct 10 2014, 06:01 PM
Return to original view | Post
#7
|
|
Junior Member
83 posts Joined: May 2011
|
deleted
This post has been edited by nzh0920: Oct 10 2014, 06:01 PM |
|
Topic ClosedOptions
|
| Change to: |  0.0451sec
 0.65
 7 queries
 GZIP Disabled
Time is now: 11th December 2025 - 11:21 PM |
Quote