front n rear bumper gap.. the front one i hit the bottom last time. any idea how to diy fix it back?
[attachmentid=4064679] [attachmentid=4064673]

plastic clip leg?? got pictures?
ya but actually i dun quite like it..

There are four metal legs holding the rear bumper. Two behind and two at the sides. Do a pulling + upwards pushing motion for the legs, but beware of bending the legs in such a way where it deforms the area the legs are secured to. it'll look very ugly.

The bumper plastic clips should be less than RM2 each the last time I bought them. Can't find cheap clips anywhere. I've broken my interior trim clips so many times after my many DIY sessions. They're also about RM2 each, or RM3 for "original" Proton clips .

This 1 should be when u open bonet middle there near radiator..paint shop have..
This 1 missing,u will hear vibration when accelerating.
rm1.20 each if not mistaken, get from paint shop when I spray my front bumper when drop off.

Spare parts shop.

They sell it individually, or at least the shop that I buy it from do.

The bumper clips don't break that easily anyway. I'd suggest buying more if you don't like slowing down for bumps enough to prevent the bumper from scraping the floor just to be slightly faster at the expense of car damage.

So good . The previous owner of my Persona clearly didn't take care of it. The front bumper has slight cracks/tears around some of the clip securing points, and plenty of scratches underneath. I also damaged the bottom of the front bumper about 3 times during the early stage of owning the car, twice due to touching the kerb during parking, and once because I didn't brother braking while going down a short ramp. Now I avoid any form of damage if possible.

Which reminds me of the stupid car respray shop I sent the car to last time. Promised to do what I requested but in the end I got nothing but shitty workmanship, like really shitty. I ended up finding some time to attempt to adjust the front bumper's metal legs myself, which was pretty damn easy to do.

The legs are located around the area below the number plate. It will be easier with the car slightly jacked up. You will see them easily as there will be two screws under there.

Yes,even when they service the aircon compressor,they will remove the 6 black thingy..and later wont put back.
U cannot argue with them..they will just say break edi..

That's why I never mod exterior, coz these serviceman don't give a dam about your car.

I got mine from the paint shop at sprint highway,dunno they will sell to u anot,coz u buy that only..lol
they sold to me as I went for minor knocking  and minor spray oso.

don't say liddat lor. not everyone is like what u said. u mau kena steering lock kah? 
if got reliable shop @ honest magician, they wont do that lor. e.g nestum tyre shop.

There are four metal legs holding the rear bumper. Two behind and two at the sides. Do a pulling + upwards pushing motion for the legs, but beware of bending the legs in such a way where it deforms the area the legs are secured to. it'll look very ugly.

The bumper plastic clips should be less than RM2 each the last time I bought them. Can't find cheap clips anywhere. I've broken my interior trim clips so many times after my many DIY sessions. They're also about RM2 each, or RM3 for "original" Proton clips .

already at kampung ... just thought about it on the way back, so cant do it.. hope everything will be ok laa. 

Mine also have minor leakage on the top and bottom.
But i add 1 STP engine stop leak to the lubricant there. Now no more leakage.
If your leakage is very serious recommend fix it asap.

Mine also same since 45k. near 70K also. Mechanic mentioned a lot of proton also got same problem. Just leave it unless it get worse.

Mine just reached 50k ytd. Edy have minor leak. Lucky notice early and solve it.
If leak again really need to change gasket or re-glue it.

top shud be able to do it by ourself. Botton 1 is hard. Unless u r mechanic.

If really worry, then wipe clean and keep jalan for another 5 to 10K, see how bad is the leak. If still same, only dry dust, not wet with no detectable reduction in engine oil, I'll just leave it.

not almost all, it's all car bearing the plotong badge will have this problem. actually this problem were faced by any car, but since is plotong badge, it's VERY NORMAL, eventhough u r uncle driving style driver.

normal as rubber easy to degrade.. thts why leak here leak there... proton love to use rubber and plastic only...