Hi guys . I started a custom scratch build recently. and here goes the build log. Stick with me to see how I did it. and let me know what you think



Initial Designs to final build. Let's go

A big Thanks goes to Cooler Master Malaysia for sponsoring my Build

Now let me take you through all the problems I faces and success I had in this build.

1st of all I'm 20 years old and I'm doing my degree in business management. This is my 1st build/mod. I'm From Sri Lanka and I stay in Malaysia

Time Frame two months, September 1st - November 1st (Before new semester start)
Time was the biggest hurdle for me.

Let's go with the story of this nice Casing
I bought this new system few months back and i got a casing for about $50. Was wondering what I can do to look my new system better.and some of my friends were showing off their cases and I was wondering whether I should spend a lot of money for a common casing or should I make a one for myself. came a design to my mind and drew it on a paper ( I'm an artist and also I can do 3D modeling). Then made a 3D Model of it. to see how it looks

Here goes it:


Then I went back to my parents place in south of Malaysia. There here I start my work with e great help from my dad.

What i did 1st was buy some styrofoam and carve the design in it according to real life measurements Made sure I left enough space for mobo and PSU, and cooling. then length to width ratio and drew it on styrofoam with a pen/pencil.then start sanding to get the curves and



Lot of sanding with sandpapers. to cut the styrofoam I made heating coil using a old soldering iron coil. Had to do it for a long time as I couldn't find thick pieces Had to make parts separately and join it later.

A big Thanks goes to Cooler Master Malaysia for sponsoring my Build

Ok today i like to tell you about what happened with sponsors. Ok first off when I was at this stage of the build I sent emails to so many companies. the only company responded positively was EKWB, They promised to give me a CPU block. So i was doing my project expecting a block from them. But when I was reaching the end of the project I knew my budget is very limited by that time. Since I'm still student and don't earn I can't ask more money from my parents. So what I had to do was to turn down the sponsorship. But I'm really grateful for them for helping me. Because if I were to get the block then I would have to buy the rest of the parts by myself and I didn't have enough money for it.

As my good friend Alfred Shuryan said, when ever a pearson is sending sponsorship request emails, you have to be short and sweet. You have to include some nice pics and attractive and professional words. so it's a tip to all of the readers.

I think since this is my first try and first build, it must be hard for companies to decide whether it's just another fake project or not.

So all of you who try for sponsors. good luck !

Here goes a big thanks to,

Ok Modders m back with some new pics of modding of the build. and today its all about the foam model of the case. :dremel:



So as we discussed before once I finished the side panels i concentrated on front n top covers. making these parts were very hard because I had to see through the shapes and sizes to match with the design. after some more long hours of sleepless nights finally most of the parts completed



Had to frequently check the regularity n equality in shape of the two side panels and also had to make sure the case is symmetrical. few hours of more correcting was put on to this to make sure the final shape was good.



Had few problems in making the top cover since the curve was to big i had to join two pieces together and as in the above pic i used pins to keep them together till they joined, but to tell the truth it didn't work. so i had to make the mold with the pins still there and then carefully remove them. :sigh:

So that's it for today everyone, I'll come up with latest updates again soon.

A Big thanks go for the sponsors for helping me with this build



till next time everyone

A big Thanks goes to Cooler Master Malaysia for sponsoring my Build

Hi guys, on this post today I'm going to do a simple review on the sponsor material I got from Coolermaster for my build, the Seidon 240M Liquid cooler and the GX II 750W PSU. I promise to keep it simple at the same time giving you all the information you need.



CM 240M Liquid cooler is very good cooling solution for Gamers and mid-range Over-Clockers. Though it’s not the latest model of liquid cooler by CM (which is Nepton) and it doesn’t look fancy like a custom water cooling loop either, it’s more than enough to keep a properly overclocked system at high stress levels. This product is comparatively very cheap, where a custom water cooling system would cost more than two or three times of that this would cost. Also the main advantage in a closed loop is that you don’t have many maintenance issues, you don’t have to clean the loop frequently or be worried of leaks. This solution is perfect for builds like mine where all the internal parts are closed so I won’t miss fancy water cooling system, but adding it to an open system will not look bad at all.

Ok now talking about the components and features let me go point wise so it’s easy to read

• Maintenance-free – for me most important because you don’t have to waste a half a day to clean my cooling solution, might be same for you. As I've mentioned before it comes pre-filled and closed loop, but there is a connector in case you want to remove the liquid.
• A new efficient design for better over-clocking performance. From cold plate and pump to radiator and fans everything is optimized for better cooling and lesser noise.
• The pump has a very durable n less noise design – 70 000 hours life expectancy and less that 25 dBA which is basically cannot be heard.
  
• Durable and Flexible tubing - This system comes with a very durable and flexible tubing, you can twist it turn it it won't break. Also the tube ends have been connected in a way that you can turn it almost 180 for different positions of setups and the tubing is long enough for nay setup you like.
• Ultrafine micro channels – which is as in the picture bellow very fine fin on the cold block to maximize surface area therefore increasing the heat transfer.
  
• Large Aluminum Radiator – Everyone would prefer it to be copper, but the prices would be different then, but the denser fin design can make up for some of that missing copper.
• PWM capable 4-pin Blade Master Fans (120CM) – these fans are pressure optimized to create and maintain enough pressure between radiator and fans. PWM fans gives control over the fan speed therefore reducing noise during low temperatures and increasing fan life
• Universal Mounting solution – supports LGA 2011/1150/1366/1155/1156/775 and AMD FM2/FM1/AM3+/AM3/AM2.
• Capable of push/pull/push-pull setups - A wide range of screw sets is included in the package.
• Very silent cooling capability - less than 40 dBA, but this can vary according to your setup and fan grills.
• Bow shaped Contact surface for best contact with the chip – It is proven that the slightly bow shaped blocks make the best contact with the processor. In the traditional flat face blocks the center of the block makes less contact with the processor reducing heat transfer.
• Copper CPU block - As anyone would expect the cold block (CPU Block) is pure cooper build and has a very smooth surface for optimum contact.
  

Apart from the above all the cables comes with a nice tight black wire sleeving.

Some people say why Cooler Master named this 240CM a “M” (medium) and the 120 CM one “XL” (extra Large), it’s because the radiator in this one is thinner than the one on 120XL, but it’s not a reason to think that the 120XL is cheaper and better, because the fin density in this radiator is higher than in the rad of the 120XL in fact it's higher than many other 240CM radiators, so still this radiator maintains that double cooling capabilities than the 120XL and also outperforms many other 240CM radiators.

The contents of the Package are as follows.



The cooling solution itself
2x Blade Master 120CM PWM fans
1x rubber seal for noise reduction
1x Fan Splitter (4-pin)
1x AMD Mounting Bracket set
1x Intel Mounting Bracket set
1x Back Mounting Plate
1x Cooler Master thermal compound
Screws for all kinds of possible setups

So that’s the basic review of the cooling solution. Soon I will update this with the cooling scores of the system.
Thank you very much for referring to my review.

A big Thanks goes to Cooler Master Malaysia for sponsoring my Build

Hi guys today is the second review of my PSU I got from Cooler Master for their sponsorship. Guess what, it’s a famous GX II, one of the most famous gaming power supplies in the market. This is one of the most reliable and cost effective power supplies in the market so far. Yes there are bigger and better power supplies, but for a mid-range budget build this PSU is the perfect solution.

• It’s a single rail 12V non modular PSU. Yes would prefer it to be modular but something to keep in mind is that it is comparatively very cheap.
  
• 5 Year Warranty – Cooler Master guarantees that their product will be functional for 5 years and it’s more than the time that you would use your computer. Unlike other PSUs this one has 5 years of coverage where most of the other PSUs give only 3 years coverage.
  
• USB charger – this is one of the top features I like in this PSU, this is a socket to connect your front USB panel through to the motherboard, the GX II provides continuous 5V power to the front panel even when the system is not running.
  
  
• Support Dual SLI- the GX II 750 W PSU comes with 4x 6+2 pin connectors, meaning that it can power up two high end graphics cards.
  
• The new 2nd Generation of GX II have a very silent fan and good cooling for long hours of operations.
  
• Built-in protection systems for stable, smooth and dependable supply like, OVP/ UVP/ OPP/ OTP/ SCP/ OCP.

Here are the Specifications of the PSU


The Power Distribution is as follows


The connectors available are,
1x 20+4Pin Motherboard Connector
1x 4+4Pin CPU +12V Connector
4x 6+2 Pin PCI-e Connector
9x SATA Connector
3x 4Pin Peripheral Connector
1x 4Pin Floppy Connector
1x USB Charger Cable

Though I wonder why they put up a Floppy Connector, it’s very good that it has 9 SATA Connectors.


The regulations this PSU comply with are a lot and you can see them on the side of the box of the PSU.


Maintenance and Dependability
Talking about dependability I have been using GX first series PSU on my old system for a long time now and used the system for long periods of time and had no problem at all with a PSU.
I have been using the new GX II for about 2 months now with my i7 Haswell overclocked at 4.5Ghz and been using the system for Rendering and Gaming for long hour. Sometime system has been up more than weeks without any problem.

Overall this PSU is a great pick for performance/price and one of the top level PSU’s available for midrange systems. This PSU has a very good Warranty coverage and is very dependable for long hours of gaming.
Test results will follow up soon.

Please visit CoolerMaster for their official specifications and detail list
A big thank goes to Cooler Master Malaysia for sponsoring my Build
Thank You Very Much