Hi jfcheong. Please add me in the 2.0 NA, white

Glad to hear you are okay, bro. Nowadays many road accident, drive safe everybody.

Hi. I just want to ask everyone here, can we install engine underbody shield to our 408 ? Will void warranty? Supplier claimed that this shield can protect the engine from water/stone and high heat resistance. Is it good to install it ? Thank you

I see. I was afraid only the heat dissipated from engine bay will reduce if install this shield. I plan to install if good. You want to install it ?

This post has been edited by chenglong: Dec 12 2013, 05:25 PM

Hi. Just share something.



this is third brake lamp, the mounting place already melted..

3+ month. 6k mileage

This post has been edited by chenglong: Dec 13 2013, 01:29 PM

No. I was found this issue through a pug 408 forum in China.

Last night, I did check it on mine 408, total 5 bulbs. All are melted due to bulbs touching on the plastic...In China, this is common problem over there, so they change the normal bulbs to LED to prevent further damage on the plastic.



You can check yours too, I can confirm. it melted

This post has been edited by chenglong: Dec 13 2013, 04:18 PM

Hi. You cannot see this socket until you open the cover.
Follow instruction below, you be able to dismantle it Remember, Use index finger at point 3.



This post has been edited by chenglong: Dec 14 2013, 10:07 PM

Now, You remove the power cable first and then use long type screwdriver at point 1 if you don't has star screwdriver on hand (Hints: short type screwdriver very difficult to turn the screw)



Me, I remove the star screw first (point 2) so I can take down entire black housing. I can easily remove screw at point 1.


After you remove screw at point 1, you will see the two clip (next to the screw) at each point 2, "un-clip" it



Then, you can take out the bulb mounting, like picture below



If you want take out the bulbs, don't use hand, use masking tape. Don't press on top to the bulb directly (to avoid break). Use tape wrap on top of each bulbs, gentle pull it left-right until it loose. like picture below



This post has been edited by chenglong: Dec 15 2013, 04:04 PM

I plan to change all the bulbs to LED, it generate less heat than normal bulbs.
I not sure under warranty or not, but you can contact to SC.

Your 408 headlamp very nice, smoked

Hi.

If you manage to claim it, you need to change the bulbs too, right? Or maybe originally it is like this.. otherwise, it will melt again..

This post has been edited by chenglong: Dec 16 2013, 01:35 PM

Home downlight on atleast few hours than brakelight just on few minute (I think less than 5W), heat will less too..
Claim warrant will do it on next service then I'll change all bulbs to LED..

Probably by circuit board/cable or grounding cable problem. This cause unstable current flow rate. drive in to the SC to check it out.

This post has been edited by chenglong: Dec 18 2013, 12:04 AM

Hi. You can try to create a 1 new folder in the pen drive and then save all the mp3 file into it.
If problem still persist, save few songs only and then try again.

When promotion ends ? After did, 120km/hr steering will smooth ?

Your folder structure looks no problem. You has another pen drive than 32GB ? 8GB for example

I using 8GB, no problem at all.
Do try it with 4GB and then feedback to us

Hi...

Anyone try Fuel injection & carburettor cleaner for the lion before (any brand) ? Can we use it ?

Thank you

Mine also faces a problem like you but at front passenger door.
Also, one of the brake having a heavy brake dust than others and origin silver color of caliper become yellowish. I seem it not normal at all. Anyone faces a same problem ?