lol, really thumbs up to this reply. i was reading this thread with so much concentration, and when i reached this reply, i really burst out laughing. lol.

btw, a noob question here. my mobo is as shows in my sig, so i was thinking, is it better to get 2x1GB ddr2 800MHz rams, or get 4x512mb ddr2 800MHz ram? will it be the same, or there'll be performance difference?

Nah, that thing burning is a panda, not ddr2 ram

yeah, thanx for the information shawty, i heard somewhere that having all 4 slots filled up can get good results, even though im not in favour of that idea though.

you think you'll still be selling those rams on end of Q3 shawty? will the ram that im thinking of getting get cheaper some more by that time? now i don't have money already, but i'll get it like in another 3 more months to go. need to save up..

and do i need to increase Vdimm to +0.4 so that i can get the timings specified with the product?

This post has been edited by rockmaniac85: Jun 2 2007, 03:49 PM

i got say u say that meh? i heard somewhere larr, not sure where exactly.

for me, i also thought of getting the 2x1gb kit.
when larr i can get more money :sigh:

joking meh? if somebody really did that, then it would be in your favour ma..

lol..

try selling em in ebay, probably got ppl who collects burnt rams..

yep, from what im seeing, D9GKX is 25-E type, similar to the D9GQG. 25-E type have good timing and speed, so i think it's better to get those compared to D9GMH, am i rite?

oh, ok. thanx for the info.

i've done some checking, and found out that D9GKX chipset is used on 1066MHz ddr2 rams. so for those ppl who's opting for 800MHz or less, D9GMH would be ideal. rite?

well, u can check the ram chip through this website..

http://ramlist.ath.cx/ddr2/

guys, i would be getting the ballistix sooner or later, pc26400 800MHz.

jus wanna ask, is it safe to set Vdimm for this ram to 2.2V? somehow i feel like 2.2V is a little too high and probably could damage the RAM.. anyone can clarify this, as well as state the best Vdimm for this RAM? Thanx in advance..

haiya, need meh? if i don't use ram coolers, it'll die faster ah? i thought u said crucial warrantied their rams at 2.2V, not lifetime warranty ah?

how much ah ram coolers? it use molex connectors or what ah?

where to find this allngap ram cooler? got in garage sale or bulk sale? how much ah? can guide me?

yeah, for a value ram to go that high, im quite surprised too.. very loose timing where it hurts most, but having really high freq is a very good plus.. very nice..

i don't have the ram cooler, so im really scared to set vdimm to 2.2V. ATM having vdimm at 2.0, 430MHz 4-4-4-12 timing.. tighten timing a bit, can't boot already.. even at 2.2V, probably must go 2.3V...

but if you can find a good d9 chip on a value ram, then that's good for you.. normally you can't find such..

jus one question, for intel c2d e6300, which is better, higher fsb or tighter timings? coz i heard for different platforms, different type of ram oc'ing will deliver better results...

erm, can you direct me to the site which has the table? i tried googling but to no avail.. sigh...

Probably all those who sell Crucial rams.. Cheap but high performance one....

corsair dominator is lousy...

still you're spending like more than rm300 to get ram. if my budget is really limiting me, then i would go for corsair lar, but if not, i rather spend more and get better rams.. extra rm100 can get super good rams already...

lol, no wonder, i was indeed shocked to see very superb performance with low latency using pc5300 card.

yeah, very good performance, but you need better cooler for your card then..

orthos stable?

if im not mistaken larr, superpi wont stress ram or cpu to 100%,

orthos does.. and you can continue stressing for longer period of time..

best to check stability is orthos..

IINM lar.. kalu silap jgn marah..