get memset 3.4 beta1

btw, what mobo are u using?

Crucial ballistix rams (with D9GMH) are warrantied up to 2.2v. Even their reference vdimm is 2.2v. I'm not too sure about value rams though but I think their vdimm can to increase to 2.2v without any problems.

Make sure you have ram air coolers to keep the ram modules cool.....

will give a try to memtest then, thanks!

I think all the RAM will still under warranty as long as the vdimm is under 2.2v... btw, i just planning to get a pair of RAM heatsink (around RM20) to cool down my RAM only, not going to those high end heat sink...

correction..memtest n memset is different software..
make sure u know what it is..

dont talk about warranty, as long is not damage u can still claiming.. once it burn becoz of the oc.. prepare ur money la..

---

Added on October 14, 2007, 11:37 pmmake sure u know ur ram very well..
dont suka2 change ur ram timing like tat.. when u change ur ram timing from loosen to tight.. u need to make sure voltage is enuff..

if u doesnt know well ur ram, i suggest to set it from earlier, and do step by step, fail to do so will make ur window cant boot at all..

2.1v without cooling, consider safe.. more than that put ram cooling onto it, experiment urself , no one can help u..

timing 5-5-5-15 with 2.0, sure still can handle..
timing 4-4-4-12 u need to pump more..

using memset just help u to save time to do the correction to get fast in superpi,
but the point is know the right voltage for it..

This post has been edited by xixo_12: Oct 14 2007, 11:37 PM

BTW wnat to ask...I'm upgrading my RAM to 2GB so will my setup :-

OC'ed E6300 to 2.75 GHZ will be stable after I upgrade to 2GB

Which one better ?

4 x 512 MB or 2 x 1024 MB

BTW i'm using GA-965P-DS3 gigabyte

Go for 2x1024MB. It is hard to oc using 4 sticks of ram.

-pWs-

ya, i know the different between memtest and memset.. thanks for remind.

I think i know what is the problem, because of using window vista now, sometimes when I OC my computer, it can't boot into vista, but able to go into XP...
sometime orthos stable at xp, but failed at vista...

for that i dun know.. tak penah oc using vista lagi..
anyway, try to oc fist using xp.. then u change to vista.. hope it work..

i know, thats why i ask TS also what Mobo hes using, so can use clockgen and oc as well and use memset to loosen timings to check max stability and stuff mer

I m using Kingston Value RAM 2GB 667Mhz 1GB is Hynix, and another one 1GB is Micron chipset

So, I Overclock it to 800Mhz without adding Vcore, should not be a prroblem right ? I don't not tune the timing etc....

As always..juz try, tune and do loads of tests..that's da only way

u dont know until u test it with testing software.. if find error, sure problem

1T & 2T memory bandwidth on Abit IP35-pro



Attached thumbnail(s)

You mean Vdimm?

Eh? No difference in speed/bandwidth at all!

What's my Ram model.....


Attached thumbnail(s)

Corsair value ram, 1GB DDR2 667MHz.

Corsair Value Ram 1GB PC5300 DDR2 667MHZ ?....

Thx BTW.

What is the optimum operating temperature for RAM?... Mine is 32 @ Idle and 35 @ full load... Corsair XMS2 6400

What device u use to detect the temperature of the RAM?

Yeah, wondering how you know your ram temperature? I think ram modules run at higher temperature than that....