u won't be disappointed springer is still on my desktop and i'm enjoying transforming him over and over again.. so simple yet every step is intricate and covers up very well.. in fact i'm so impressed and having fun posing and transforming springer that blitzwing is still in the box

soon soon.. i'm having too much fun with springer.. he really is one hell of a figure.. i must say hasbro surprised me with this one, compared to the crap the lines were turning into

from what i can tell, it's not a bad figure, just that it has QC problems.. seen some fixes and people have said it vastly improves the figure.. i'll try it out for myself later on

This post has been edited by HxiiiK: May 12 2013, 06:40 PM

yeap, hence i mentioned QC issues.. shaving down the plastic will help lock the arm in properly

yeah blitzwing has a very squared out look, as opposed to springer which has a more sleek silhouette.. to each his own though, i think both of them are fantastic.. no time to fix blitzwing's shoulders yet though, will get on it later in the week

u can give this one a try.. however i doubt it's as permanent as sanding down the parts

yeah when i watched the video i was thinking hobby putty would be easier.. but i want to wait till i have time and sand down the plastic for a more permanent fix

dah biasa gunpla should be no problem fixing

This post has been edited by HxiiiK: May 13 2013, 10:25 AM

if the plastic is too thick that the shoulder joing cannot connect, i think nail polish will not help either, since it won't be nearly thick enough to reach the other side hobby putty will work but u leave an ugly blob inside the shoulder area.. not obvious, but u know it's there therefore, sanding is the best way to go.. go practice

tripticon then retire come back again lagi.. neverending cycle

for all you know, that may cause you to spend more than when u were collecting TFs

abang roy tu nafsu banyak TF is only a minor one

sama, letak dlm kotak lebih besar saja, and some parts molded in clear

not even any new accessories.. hasblow.. milk mmg milk

This post has been edited by HxiiiK: May 13 2013, 02:06 PM

the limbs are too splayed apart.. and the hasbro team does not seem to have anyone who can get a decent pose out of figures check peaugh's review.. he already reviewed abominus a while back and i think it looks pretty good

shi-.. u say small then i go find pics.. really small couldn't get an idea of the size cos i don't have hercules
but this i ada

fuuu.. lu dapat so cheap.. i dapat RM10 more expensive than u

pity ol' blitzwing.. he's not a bad figure, just that the QC issue and the fact that he comes with springer.. puts him in springer's shadow kesian

i think blitzwing had one forgot where i saw it.. and it specifically says 'does not fix blitzwing's shoulder problem'

actually they never fixed it.. their's was a lucky batch, maybe.. the problem varies, since it's a QC issue.. some may find almost no problems at all

epoxy putty to push the shoulder part closer to the front so it locks
otherwise, disassemble and sand down the body so the gap on the sides are not that wide, allowing the shoulder to lock in place

because the issue right now is the shoulder cannot reach the front section of the chest to lock properly

too lazy to search for the vid tutorial now, but seibertron had it a few days back.. go scrolling back if you have time, both options are properly detailed in vid form

This post has been edited by HxiiiK: May 13 2013, 11:26 PM

slowpokk, i sudah show but he does look good.. not sure how i feel about the tire rotors and his armored car mode has huge tires

finally got my hands on RTS Prime.. to add to my team of Primes poor man's team only, satu MP pun takda
now finding cheapo battle tanker for RTS Prime



This post has been edited by HxiiiK: May 14 2013, 03:04 PM