wah...KVR can go up to 500 is impressive. but the only thing i dont like KVR is that the timing starts at 3.0 compared to 2.5 (Corsair value)

So, as long as it's a BP PCB I can push 3.0V? What about the ICs?

My KVR DDR400 doing 500 Mhz flawlessly


Too good for a value ram.

Based on Samsung UCCC memory, I think can go higher, have to do testing some more 

i tought KVR DDR400 with hynix bt-d43 also can do 500 flawlessly....

Here's a little screenie:

DDR512, 3-4-4-8 @ 1T, 2.65V


Not bad eh for value rams Might be able to prime longer but I need to use my computer, gaming time

hey ur ram using BP pcb if im not mistaken rite?.. it should be go a little higher.. tweak more dude..

hey ur ram using BP pcb if im not mistaken rite?.. it should be go a little higher.. tweak more dude..
what is the pcb they're using n what is the chip weeks?..

Did you install it along with other rams? And try to use lower voltage, mine can't prime stable at 2.75V but at 2.65V ...
Yeah, it's BP PCB. My motherboard doesn't allow as much tweaking as DFI boards, so I guess it'll be a little harder. Will try upping some MHz tonight, and then more priming

Correct, I bought mine from Cyclone87. However, you and mine might differ a bit. The pair I got are Apacer retail units while yours was from a Dell system, right? With copper heatspreader if I remember correctly.

You bought the RM300 ones is it? The RM300 ones he did state can do 240MHz ~ 250MHz depending on your proc and board.

I know he's selling 3 pairs. 2 pairs Apacer and another pair from Dell with copper heatspreader.

probably chipset limitation? i saw u're running P4 there

probably chipset limitation? i saw u're running P4 there

izzit? wat limitation? see my sign?  i dun think my proc limit..
i try in my nf7 oso the same 1

-5B G - This is a newer revision of the -5B C ram. It is still 5ns ram, but can clock higher than its earlier brother. This is the ram commonly found in Crucial Ballistix that has earned quite a reputation for doing very high clocks with great latencies. It can be considered as somewhat of an "in-between" ram, meaning it does pretty decent timings with pretty decent frequencies. Most revision G ram does about 250-260, but can retain the timings of cas2.5-2-2-X. This is better timings than many of the Hynix offerings, but you will pay a price for it. Currently, 1gb of the Ballistix is around $250 USD. If you can find these chips on any other sort of Value ram, it is QUITE the bargain. It also seems to be less picky of a motherboard than some of its competitors. Identifying this ram is just like the rest...the part number will be -5B G on the ram chips themselves. Like I mentioned earlier, it is found in Ballistix and some, but not many Value ram offerings.

Woa, the one on top is a real nice baby

Quote from the RAM's Handbook:
You are real lucky

hy there, can my this KVR oc to?pretty confuse wor, bout the samsung, hynix, model n so on...just asking wor...

the micron will OC decently well, probably around 250fsb @ CL2.5 , factor in the PCB quality and etc

Elpida?    ..it's kinda the '2nd' grade of chips 

the micron will OC decently well, probably around 250fsb @ CL2.5 , factor in the PCB quality and etc

Elpida?    ..it's kinda the '2nd' grade of chips 

I have tried KVR Micron like the pic on my nF2 last time. It won't go beyond 220MHz.

You sure it's the same Micron chip? There are a few versions of it.

owh.... xxxx

i just saw one of those ram in a shop....

but never knew what they were...

i was eyeing for a dt or bt d43 or tccc

and in the end got myself a bt-d43

oo0o well..

Not my luck....

after a few hours of burning in

i am able to increase FSB to 220 @ 2 - 3 - 3 - 11 , KVR BT and DT - D43

try 2.5-3-3-7.. you will gain more Mhz 

er..did u can prime stable atr 220 Mhz speed ?

erm... yeah stable for 10 mins.... hahaha......

then KO

but i have changed a few settings it seems stable now...

but i have to reprime to make sure

10 minutes only Must be at least 12 hours

i know...

after 10 mins  .... selamatlah.....

huhu...

FSB 221 @ 2 - 3 - 3 - 11

after 6 mins of prime..... bye bye

owh.. well that was using BY SPD , now it is set to AUTO

where u bought the 1G ram with samsung uccc chipset?
for KVR how much ar?
when u bought? last time i find dun have....

hy there, can my this KVR oc to?pretty confuse wor, bout the samsung, hynix, model n so on...just asking wor...


the question is, how to read?

i can only get 215MHz after primed 6hrs wif 3-3-3-5.can i get any higher?at this speed, i even increase the dram voltage to 2.7 n cpu voltage to 1.425.do i need to decrease the multiplier?

  AMD Athlon 64 3000+ Venice (S-939) 1.8GHz (Multiplier 9) can get higher? say 10 or 12 multiplier?

215MHz for the Micron or ELPIDA?

And no for the second question. Athlon 64 3000+ has a multiplier of 9X and below, if you want procs with unlocked multipliers get the FX series

both of them...mayb tak sama chipset cant get any higher aaa? 
ic, fx series, opty? means those unlocked multiplier can get higher/lower the multiplier?wat i'm trying to say is, the max multiplier is 9x n the fx can beyond the max multiplier? 

I think the ELPIDA hit the end of the road ade, bottlenecking your Micron. For Opteron and Athlon 64, they can't go higher than their default multiplier (Exp: Athlon 64 3000+ max is 9X, Opteron 144 max is 9X). As for the FX series, I think is 4X to 25X Not too sure because I don't own one.

Still ... 220MHz is kinda low for BT/DT-D43s standard

so, shud i just unplug th elpida n try wif single channel micron?work aaa?
i get it, there's no way can go byond max cpu multiplier rite, so say, wif my a8n-sli premium+512mb kvr micron+venice 3000+350W enermax, wat r u suggest?memory timings?default is 3-3-3-8, now wif both module running at 3-3-3-5 @ 215Mhz 2T - cannot go to 1T, dunno y..just hang at the windows booting.

erm.... this is my current setup...

AMD athlon XP 1800 ++  @ 220fsb x 9

BT-D43 256 , DT-D43 256 @ 2-3-3-7 @ 2.9v

any recomendations ??

D43s can clock well @ 3-4-4-8 timings. For 2-3-3-7 I think that would be as high as it could go.

both of them...mayb tak sama chipset cant get any higher aaa? 
ic, fx series, opty? means those unlocked multiplier can get higher/lower the multiplier?wat i'm trying to say is, the max multiplier is 9x n the fx can beyond the max multiplier? 

Wow..that chip...i used to have it. Running great at 11-3-3-3.0 1T. I love voltage..like Bh5..at 2,9v.max around 235mhz..but at 3.2v..it can do 270mhz. Not sure if 3.5v.

D43s can clock well @ 3-4-4-8 timings. For 2-3-3-7 I think that would be as high as it could go.

sorry....

my timings is

2 - 3 - 3 - 11 , not,  2 - 3 - 3 - 7

FSB 215 most stable....

shud i decrease the multiplier ??