which is better to burn ram?
SP2004 or memtest?
my fwen said memtest is more powerful in burnin.. but i try the memtest..no error for 5hour..then when i try wif the SP2004..
4minute..error ..

so, how baut sifu2 and otai2 in lyn..

sorry..i'm nubie in O/C'in

i think sp2004 give more toucher to ur hardware..

I use DOS/BIOS based Memtest86

This post has been edited by soulfly: Mar 23 2006, 06:46 PM

well, it seems if u can pass memtest86(dos) with flying colours, it still not guaranteed u can run at those speed in windows error-free
windows based memtest come in handy

but for burn in, yeah, memtest86 should do the trick
btw, u should up the fsb/ram speed till few error appear in each loops..
then burn in with the errors..
if u r lucky after burning in for sometime, u may have error free at the speed

good luck

yeah.. i wonder y..
my dtd43 can run at 232 ony.. ..
maybe burn in will help me...

probably timing too tight, low volt, or ram too hot/no active cooling..
well, my dt-d43 able to do 3-4-4-10 memtest stable n 2.5-4-4-10 sPi 32M stable at 265 1T 2.8v
probably juz my luck

wow... thanks for the tip e-jump

sounds great....

i have never tried memtest or sp2004 before....

i only prime to test stability....

maybe i can try to keep the memtest and sp2004 for future use....

SP2004 is prime also, just that name and interface change only
I use prime + SuperPI for windows stability
For RAM, mostly use DOS base memtest86 because it can test almost all the RAM available in your rig

oh, one more thing, its best to run burn in a straight few hrs [ie 8++hours] compared to 2+2+.. hours..
and i guess i gain nothing after my next few burn-in sessions.. 265 was max n achieved on 1st burn in attemp..
but that may be just me.. if u r lucky u might gain more..

oh btw, if u dont have DFi , u may be limited to few memory timing options to get memtest86 error free.. theres possibility u can up a lil more mhz in windows with help of a64tweaker n pass windows memtest..
well, thats my experience

wow..damn nice..mine d43 oso..but ...
i'm using 2.5 -3 -3 7..stuck at 232Mhz ony..izzit my timing too tight ?...bottleneck wif my ram..see my siggy

well, cant say much there..
my ram was able to do 2.5-3-3-10 till 250
how bout u try a few loop of memtest test 5 with
3-3-3-x
3-4-3-x
2.5-4-4-x
3-4-4-x

but its best to go with the loosest 1st [3-4-4-x] juz to know how high ur ram can go
saves time too
timing tightening comes later

ok..will do it tonite!..will burn in untill tomolo morning
then tomolo will post the result..

huh dude..mind to tell us ur result..

to increase fsb.. hynix like loose timming..
my bt-d43 put 10-5-5 2.5cl 2.7v.. just an option to loose timming..

after 8hours burnin wif memtest.. now my ram can run at 235Mhz..
will try more tonite..

This post has been edited by nelza_ax: Mar 24 2006, 05:11 PM

SP2004 / Prime95 stress on the CPU, FSB and RAM, whereas memtest just test the RAM. That's y if your RAM is stable, it doesnt mean other stuff is stable also.

One more thing that do influence the end result is the BIOS of the mobo. Do take that in mind. Compare your result with similar motherboard and the revision of the bios. modded or such. That way you'll know what went wrong with your setup.

Burn ram : memtest (i prefer to run dos n windows..)

Burn cpu : CpuBurn

bt-d43 works well enough with Trp=4 and Trcd=4 .... using 5 won't help anything... at least in my experience.

263mhz, CL2.5-4-3-11 @ 2.9Vdimm was my best one on nForce2.

hey..which is better? burning ram in error or without error?
erm.. i mean my ram only can do 235Mhz but last nite i run the memtest at 240Mhz....got many error dis morning

or should i burn it at 235Mhz only?