Welcome Guest ( Log In | Register )

Bump Topic Topic Closed RSS Feed
3 Pages  1 2 3 >Bottom

Outline · [ Standard ] · Linear+

 PROTON SAGA BLM, FL, FLX CLUB V38, 生生 发发

views
     
coolkwc
post Jan 11 2013, 02:31 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(wanfauzan @ Jan 11 2013, 12:21 PM)
hi,

after changing the blackened cabin filter, still lemas when idling behind lorry...  icon_question.gif  need to open the window, otherwise will suffocate to death.

coolkwc how does your diy improve your cabin air quality?
*
wanfauzan

Since that day never smell outside air when air circulate inside cabin. Purposely go behind those hutan bakar lorry also same. So far din fall asleep due to outside air blockage.
coolkwc
post Jan 13 2013, 02:51 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(wanfauzan @ Jan 13 2013, 02:22 PM)
just finished doing door rubber seal for my gaga.

my observation:
- minimal to none improvement of outside sound.
If u start soundproofing from door rubber seal, yes, almost no effect. Last time what i did is soundproof doors, floor, mug guard then only door rubber seal. And the effect is huge,  like from stereo to mono, if u understand what i mean.

- nice sound when opening and closing the door. almost same sound and suction effect on satria neo r3 tested in the showroom.
Yes, but still too far even from Persona.

- door a little bit hard to close. need to slam a little bit.
Normal, wait for few weeks.

- rear door hard to open. I need to pull the door lever all the way before the door open. this applies to all two rear doors. front door dont have this problem. I am afraid my passenger will unfortunately break my door lever. I dont have any idea how the rubber can affect this, as the mechanism for door opening is all mechanical. hmm.gif
When u put rubber seal between door and door frame, the rubber tends to push the door outward, which will tighten the door mechanism. Normal, wait for few weeks also.
*
This post has been edited by coolkwc: Jan 13 2013, 02:52 PM
coolkwc
post Jan 13 2013, 02:59 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
Currently practicing single de-clutch downshifting.

1. Pull from let say 5th gear to N without clutching.
2. Then step throttle to bring up RPM.
3. Clutching and shift to lower gear, de-clutch...

I found this is more faster than double declutch and research over internet no harm to tranny too.

This post has been edited by coolkwc: Jan 13 2013, 03:00 PM
coolkwc
post Jan 13 2013, 03:04 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(wanfauzan @ Jan 13 2013, 03:01 PM)
seems like I need to wait few weeks for the rubber to soften. by the, still got extra big D rubber after applying for all 4 doors.
Want to make double layer but it starts raining. maybe next week.

btw, any improvement regarding your outside air intake filter diy?
*
I replied adi...

QUOTE(coolkwc @ Jan 11 2013, 02:31 PM)
wanfauzan

Since that day never smell outside air when air circulate inside cabin. Purposely go behind those hutan bakar lorry also same. So far din fall asleep due to outside air blockage.
*
Is totally solved, not improve.
coolkwc
post Jan 13 2013, 03:35 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(wanfauzan @ Jan 13 2013, 03:12 PM)
sorry, mislook.  icon_rolleyes.gif

glad that solved the problem.

Thinking just to tape a piece of cloth at the intake under windshield, as your DIY beyond my level.

Btw, if your sponges are soaked with water, after few days dont they will smell nasty?  hmm.gif
*
Very hard to explain here, u have to dismantle the panel and observe urself, u will know the sponges will not soaked with water for long time.

Ur u tape a cloth there? U have to dismantle the panel if u want to put the cloth inside.
coolkwc
post Jan 13 2013, 04:12 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(wanfauzan @ Jan 13 2013, 03:43 PM)
I plan to tape a cloth outside, but the the car will look hideous.

How to open the panel?
Just pry it open?
Do I need to prepare some clips in case some clips are broken?
Where can I find the clip?

Man, thats a lot of questions.  tongue.gif
*
No, the clip is located inside the rubber between the panel and hood.
There are total 6 clips per panel, 4 of them have to cut it off, i try almost 30 minutes and failed to pry it off without break it. So finally i cut them all away. Just go to those car part shop to ask for the clip.

These 2 no need to cut off.
Attached Image

Remained 4 pcs along same panel just cut it off, dun waste time, ori part is so damn tight and can't pry off without break it.
Attached Image

Replacement clip.
Attached Image
Attached Image

If u are not able to do so, just send to aircond shop to seal for you la, price i dun know...mine is seal with sponge, so I still can use the outside intake, just slower air flow only. If permanent seal, u won't be able to use outside intake anymore.
coolkwc
post Jan 13 2013, 05:38 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(mengsuan @ Jan 13 2013, 05:26 PM)
Yeah, I used to do this. If you're familiar, can even shift without clutch.
*
Shift without clutch might increase synchronizer wear and tear, not recommended.

This post has been edited by coolkwc: Jan 13 2013, 05:40 PM
coolkwc
post Jan 15 2013, 11:38 AM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(GP mad man @ Jan 15 2013, 11:24 AM)
can i know what is the purpose for this?
downshift 2 gear i do it all the time, upshift 2 gear...
1st time  laugh.gif
*
What so special jek...manual stick is free to play geh, dun worry too much...
Suppose you shift to 5th gear @ 80km/h, now i 2nd gear rev to red line, already reach 80km/h, then i just change to 5th gear la...

The purpose of this is lazy to clutching and shift gear... laugh.gif
coolkwc
post Jan 15 2013, 02:14 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(GP mad man @ Jan 15 2013, 12:38 PM)
sweat.gif i 5k also scare liao, u go red line.
what is the feel anyway?  unsure.gif
hmm.gif yeng? jek hai mie ye?
*
Campro not so fragile geh, u go try ma know lo... whistling.gif

Since u say 5k, then i talk 5k.

Sometimes cruising @ 60km/h, u need to overtake car, so u shift into 3rd gear and potong it. When u finish potong, is around 4.5-5k rpm @ 3rd gear, which translate into around 90km/h adi, so takkan u still shift to 4th gear then shift again to 5th gear ma, just shift from 3rd to 5th will do.

Sometimes rev 2nd gear to red line is becos some sohigh move too slow when traffic light turn green....

This post has been edited by coolkwc: Jan 15 2013, 02:17 PM
coolkwc
post Jan 15 2013, 02:38 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(GP mad man @ Jan 15 2013, 02:29 PM)
flex.gif haha, i see...
the bold part, other car thaught fighter jet just take off from beside. ph34r.gif
but i know kenjilew somebody at here driving 190kmh, isit 5th gear red line liao?  unsure.gif
*
Yup, i can shift to 3rd gear, but scare the engine noise not enuf to remind those sohigh. Red line engine noise to told that sohigh me and my car is rage. whistling.gif

No, red line can reach 210km/h. 190km/h is around 6.3k.
coolkwc
post Jan 15 2013, 02:51 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(eqmal197 @ Jan 15 2013, 02:45 PM)
huhuhuh. cvt gaga redline at 6k. confirm cannot go 190kmh. is about 181kmh  whistling.gif  whistling.gif
*
I believe FLX CVT max speed is determined by TCU rather than engine RPM.
coolkwc
post Jan 15 2013, 03:17 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(eqmal197 @ Jan 15 2013, 03:08 PM)
some say it has been cutoff limit to 165kmh as advertised in their brochure
but some say it can go beyond that. i've seen somewhere in youtube they belasah FLX SE to 200kmh
*
You imagine la, if CVT can cruise @ 110km/h @2600rpm, by right 5200rpm ur car can reach fly-to-the-moon 220km/h kind of top speed adi. But the fact is:

1. When the car speed keep on increase, wind drag increase drastically, so when u reach 5200rpm, ur car can only go around 180km/h only, becos TCU will auto adjust the gear ratio based on ur throttle input and torque required, so even ur RPM can reach 6000rpm, maybe u still only able to maintain @ 180km/h.

While manual is not same, the gear is 'real', once engage and lock there, it will totally depends on engine capability (unless ur clutch slip). if i can cruise 110km/h @ 3600rpm, i sure can reach 220km/h @ 7200rpm, the problem now is whether the engine is capable to run that fast @ that speed only.
coolkwc
post Jan 15 2013, 08:59 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(zeone @ Jan 15 2013, 08:35 PM)
Hi Bro... notworthy.gif
IINM 2nd Bulk is still ON...  thumbup.gif
Pls contact/PM Bro Mahihi.... cheers.gif

Mahihi 1 more interested Bro 2add 2list for 2nd Bulk of OBD....
*
1 more here. nod.gif
coolkwc
post Jan 16 2013, 12:13 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(GP mad man @ Jan 16 2013, 11:03 AM)
wa tarak fog lamp nor spot light, no wonder nobody want to let me overtake at fast lane cry.gif
*
Engage to 3rd gear, stick to their butt and standby, 3rd gear till red line can achieve 120km/h geh... whistling.gif
coolkwc
post Jan 16 2013, 12:22 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(dares @ Jan 16 2013, 12:14 PM)
U try convoy with him, he stick to your butt close close wan  whistling.gif Almost as terer as Nick
*
He can't get close to me one la... whistling.gif i go red line, he only dare to go until 5k rpm... whistling.gif

This post has been edited by coolkwc: Jan 16 2013, 12:23 PM
coolkwc
post Jan 16 2013, 01:37 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
His car burn air only kot... laugh.gif
coolkwc
post Jan 16 2013, 04:35 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(davidke20 @ Jan 16 2013, 03:35 PM)
Engine rosak community

wub.gif cum lar, u will like it geh wub.gif

user posted image
user posted image

500km/tank no plobrem wub.gif

Engine rosak fuel seb bulk:
1) dared
2) iska
3) r3apers
4) gpmm
5)
6)
7)
8)
9)
10)

Hurry! While stock last laugh.gif
*
My car now 355km still got 2 bar fuel...

So what, rosak since i got my car... yawn.gif whistling.gif
coolkwc
post Jan 16 2013, 04:37 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(davidke20 @ Jan 16 2013, 03:48 PM)
» Click to show Spoiler - click again to hide... «

Refer to pointer 8. That's where exactly the experienced tyre shop need to fix. They'll have to unload the brake hub, add washer to the top mounting space so your tyres can be straight. In order to make sure washer added doesn't cause your camber outward(+ve value), each washer goes in will have to put back everything and check alignment again. If still off, will have to unload everything and redo adding washer until it's straight. Therefore it's slightly more expansive. However, some shop willing to do at decent price. As for the shop I've recommended, they charge RM130 if not mistaken. Going up and down from the machine, taking off brake hubs like 10 times. I see ady also think well worth the money I've spent.
In bulk list ady whistling.gif
*
Last time i did only RM90...
coolkwc
post Jan 16 2013, 04:41 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(davidke20 @ Jan 16 2013, 04:38 PM)
Bless you to have 600km/tank then yawn.gif
*
Unless i got LC2K certified of 20km/L...oh my, Luke's car also engine rosak... shocking.gif
coolkwc
post Jan 16 2013, 05:13 PM

Fall in love with audio again.
*******
Senior Member
3,112 posts

Joined: Jul 2006
QUOTE(GP mad man @ Jan 16 2013, 04:25 PM)
mmg funker betui...

btw, using 2k rpm concept 2 days...
normally 2 days drop 1 bar but now now now still no drop ph34r.gif
maybe terkena YAB mia sumpah liao??? icon_question.gif
*
Nothing to do with 2k concept at all.

When u purposely want to monitor ur FC, sure ur right foot will aware and press gently one.

3 Pages  1 2 3 >Top
Topic ClosedOptions
 

Change to:
| Lo-Fi Version
0.0544sec    0.72    7 queries    GZIP Disabled
Time is now: 10th December 2025 - 01:15 AM