Maxis Maxis 3G/HS 4G Thread V8 (Not WBB), It's time for LTE now :p
|
|
 Dec 19 2012, 10:36 AM
Return to original view | Post
#1
|
 
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr 
|
QUOTE(vez @ Dec 18 2012, 11:13 PM) anyone have iPhone 5 to try with Maxis 3G, how is the speedtest result? it depends on location, i can get 10Mbps down in location A but getting 1Mbps down in location B |
|
|
|
|
|
Dec 28 2012, 06:42 PM
Return to original view | Post
#2
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(greenlp_87 @ Dec 28 2012, 04:19 PM) HOW TO KNOW THE CHANGE EFFECT??ANY CLEAR DIFFERENCE ON THE SPEED AFTER PROPERLY CHANGE THE MTU VALUE? u can run ifconfig in openwrt cmd line and look at the MTU value for your Point-to-Point Protocol interface |
|
|
Dec 28 2012, 07:10 PM
Return to original view | Post
#3
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(chuahcs79 @ Dec 28 2012, 06:59 PM) Off Topic : hey bro, hey bro,. is there any straight direct command can tweak the openwrt 3G wan MTU to 576 via Putty SSH ? i dun have openwrt with me now...u may try the following command 1) run ifconfig to identify your 3G wan interface 2) if u have identified it as 3g-wan, then run below: - ifconfig 3g-wan mtu 576 3) then run ifconfig again to compare the mtu per 1st ifconfig output if anything goes wrong, you may reboot the router. hope this help. |
|
|
Dec 29 2012, 01:16 AM
Return to original view | Post
#4
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(greenlp_87 @ Dec 29 2012, 12:02 AM) can explain step by step to do this?im newbies 1) Download PuTTY - http://www.chiark.greenend.org.uk/~sgtatham/putty/ 2) PuTTY to your OpenWrt using SSH connection type 3) Enter the same login and password from WebGUI or LuCI 4) Then run ifconfig and identify your 3g WAN like below: - 3g-3g Link encap:Point-to-Point Protocol inet addr:1.2.3.4 P-t-P:1.2.3.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:3986 errors:0 dropped:0 overruns:0 frame:0 TX packets:3950 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:465666 (454.7 KiB) TX bytes:456150 (445.4 KiB) Note: My MTU is 1500 and I using Celcom 3G. Maxis 3G inside my house only able to get EDGE. |
|
|
Dec 29 2012, 01:46 AM
Return to original view | Post
#5
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(greenlp_87 @ Dec 29 2012, 01:35 AM) ok..i found the line..then how to change the mtu?whats the command? u can try example below (example 3g-3g is the 3g interface): -ifconfig 3g-3g mtu 576 u can reboot to revert. |
|
|
Dec 29 2012, 02:04 AM
Return to original view | Post
#6
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(greenlp_87 @ Dec 29 2012, 02:01 AM) try already...after change the mtu insert the command it change but after reboot the mtu change back to 1500...how to solve? please post #1161 by yeop if u want permanent solution. |
|
|
|
|
|
Dec 31 2012, 06:14 PM
Return to original view | Post
#7
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(chuahcs79 @ Dec 31 2012, 04:59 PM) if u are not on DC_HSPA+, there is a slight chances u are conencted to UMTS900 cell tower with HSPA+ Max transmittion bro, so to achieve DC-HSPA+ speed, need 2100MHz? thanks. |
|
|
Dec 31 2012, 06:37 PM
Return to original view | Post
#8
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(chuahcs79 @ Dec 31 2012, 06:17 PM) actually UMTS900 Also can achieve DC-HSPA+ but due to maxis didnt really ON DC capable on UMTS900, ok. so UMTS900 mostly all up to HSPA+ single channel only i dun hv DC-HSPA+ modem, so i cant test. summore not using maxis. |
|
|
Dec 31 2012, 06:44 PM
Return to original view | Post
#9
|
|
Senior Member
898 posts Joined: Jan 2003 From: ph/sbj/slgr
|
QUOTE(chuahcs79 @ Dec 31 2012, 06:41 PM) well u mobile also have DC_HSPA+ as well,. celcom ada tak  ? hehehe...sikit off topic |
|
Topic ClosedOptions
|
| Change to: |  0.0428sec
 0.60
 7 queries
 GZIP Disabled
Time is now: 10th December 2025 - 11:49 AM |
Quote