While waiting for few parts to arrive (The Revival mods) decided to do something with my old PC which is use by my mum now.
It was my old mod (first mod) done by me...
the heck i'm doing....
keep re-modding old mods (i'm an average dude with no incoming funds and full time unemployed for the time being).LOL

previous state/appearance/etc



if u guys did followed the worklogs' section or active in it back in 2008 u might came across with my first project.
the full worklog can be found below and please ignored the ingelish*

http://forum.lowyat.net/index.php?showtopic=704381&hl=

This post has been edited by irienaoki: Dec 8 2013, 11:46 AM

see how bad it looks now..
after 4 years.





no need of 5.25 + 3.5 bay
throw it away

custom alu plate with switches and clear acrylic window on top of the case


custom alu plate for the back too.


custom midplate/psu cover + custom mobo tray from acrylic/aluminum.


This post has been edited by irienaoki: Nov 7 2012, 04:59 PM

Wa so creative abang ilie.

This rig getting wet oso ka bro~?

Air cooling only since the hardware spec are really cikai.
it s better for me to spent on hardware rather than wc for now.
gamer mum never need WC.

cardboard templates


Tri Fans for front Intake






gooding stuffs


This post has been edited by irienaoki: Nov 12 2012, 05:45 PM

tkde keje la tu

where u get the alu plate bro?

it s cardboard just for templates.

A small update for the front panel and mobo tray.
No hardware for the moment so do ignore the board, will ya.





the Slipstream will be replaced with normal 120mm fans (25mm thick).


acrylic mobo tray.
using L mounts/hinges and screws to mount it on the main chassis.




YES awesome board (sponsored) LOL


the pink tray is the original mobo tray for this case and will me throw far far away.






This post has been edited by irienaoki: Nov 22 2012, 08:21 PM

recycle the original standoffs from the old mobo tray.
to bad i forget that i have plenty of it (chrome) from my lian li cases.


Looks good (mobo tray was not mount to the frame yet).




only have 6 of it and the lian li's is smaller than the old case so i cant used it on the acrylic mobo tray.
dang it!!!


fitting test.


This post has been edited by irienaoki: Nov 22 2012, 08:26 PM

jigsaw dead already and i forgot where did i put the cutting disks for dremel, twice.
so only can update on hardware for now

temporary hardware
e8400
asus p5q pro
zotac 9600gt (ignore the gpu inside the picture)
cm extreme psu
2x2gb KVR





This post has been edited by irienaoki: Dec 9 2012, 02:44 PM

richie rich irie

was thinking of DFI X48 UT or ASUS ROG to use for the project but too bad no luck.

so have to stick with old dfi board
x48 DK

replica from cardboard




2 layers of heatsink (final material is 1mm aluminum plate)

cardboard prototype

i like the way u mod ram...haha thumbs up

too bad cutting aluminum plate will be lot hard than a cardboard.
LOL

the ink on the ram pins wont spoil it ka?

---

Added on December 29, 2012, 8:22 pmthe ink on the ram pins wont spoil it ka?

This post has been edited by ntw: Dec 29 2012, 08:22 PM

using old faulty ddr ram as the based

but will it spoil if kena the ink? just for information..

not sure perhaps it do.
u can try it for urself LOL

nice idea...I can steal this idea to mod my rig also hahaha...coz I am using corsair value ram

doing some painting job
based paint

thinking of equipping RX360 inside the case

some update on the project
decided to go with this design.
since i have no experience in 3D rendering program decided to do it with cardboard, like usual.









This post has been edited by irienaoki: Jan 19 2013, 11:53 PM

done
















This post has been edited by irienaoki: Jan 19 2013, 11:55 PM

Bro, i really respect your skills and creativity. Keep posting pls. Thx

like your design..so creative..

thanks guys.still deciding whether to use acrlic or aluminum as final material.

Star Wars bro~?

Did u study architecture or something? nice work with the design bro..
In that type of design, i'd go for shiny alluminium
Kinda have that futuristic type of look

nope
graduated from Law school.haha.

whoaaa the design is so nice and neat

ur this project already finished? or still on hold?

i like the idea =)
looks great
awaiting ur next update, seeing it caused a spark in my imagination

lol like a spaceship?