rechip for ur evo engine???
LYN Proton Wira Club (LYN-PWC) V-XXVIII, Wira 4ever.....
|
|
 Jul 27 2012, 07:51 PM
Return to original view | Post
#1
|
 
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader 
|
|
Quote|
|
|
|
|
Jul 28 2012, 10:26 PM
Return to original view | Post
#2
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
wira 1.5GLi (A) Rm80 ron 95@rm1.9/L = total 430km then engine stall due to fuel shortage =___=!! finally learn hard lesson on how wira response when not enuf fuel...
|
|
|
Aug 8 2012, 08:22 PM
Return to original view | Post
#3
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
QUOTE(GKWong @ Aug 8 2012, 03:32 PM) Yea.. planning to get the block then send to rebore and rebuild it with 4G18 stroker kit then only swap with my 4G13 my place so few halfcut shop available... last week went to asked one halfcut shop, he said all whole set engine together need 2k+  rebore and rebuild wit 4G18 stroker kit total cost how much??? will it be more fuel efficient than 4G15??? since become 1.6L already haha  This post has been edited by jay: Aug 8 2012, 08:29 PM |
|
|
Aug 8 2012, 10:17 PM
Return to original view | Post
#4
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
QUOTE(xxboxx @ Aug 8 2012, 09:21 PM) Should be more fuel efficient, but ultimately still depends on your right foot. if can do better than 9.8L/km then good enough for me liao hahaha   price for conversion??  |
|
|
Aug 9 2012, 08:06 PM
Return to original view | Post
#5
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
QUOTE(shinjite @ Aug 9 2012, 11:33 AM) Quite pricey pricey as in pricier than engine transplant??It should be more fuel efficient as your cc already increase, torque also increase Very good low end torque  |
|
|
Aug 18 2012, 08:36 PM
Return to original view | Post
#6
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
 if got oil stains around the circle part at the valve cover means need to change gasket already?? |
|
|
|
|
|
Sep 11 2012, 02:10 PM
Return to original view | Post
#7
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
yesterday sent my wira to service oil leaks and aircond pulley
can sifu here see whether i got kena potong kepala anot : power steering oil change - RM120 Valve cover gasket - RM25 Distributor oil seal - RM65 labour for oil change - rm5 --------------------------------------- total rm215 ====================== aircond fan motor - rm195 recond aircond clutch pulley - rm60 shaft Bearing - rm18 clutch coil - rm68 fan belt - rm10 aircond gas and labour - rm25 ---------------------------------------- total rm370 ======================= grand total - rm585  |
|
|
Sep 11 2012, 07:50 PM
Return to original view | Post
#8
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
QUOTE(shiyau @ Sep 11 2012, 07:26 PM) what power steering oil you using that cost RM120?! duno but the foreman say he will clean the whole steering system with machine, i kena potong ady??   |
|
|
Oct 15 2012, 10:49 AM
Return to original view | Post
#9
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
anyone went to Mean Machines 2012 autocity?? saw this wira with awesome stance setup
  |
|
|
Nov 15 2012, 04:43 PM
Return to original view | Post
#10
|
|
Senior Member
904 posts Joined: Jan 2003 From: Central Region Status: Safe Trader
|
guys, wira 1.5 front anti-roll bar is 20mm right? can change to wira 1.6 23mm one??? my foreman said bracket and mounting hole not same cannot direct change wor, and new 20mm ARB cost rm125
 |
|
Topic ClosedOptions
|
| Change to: |  0.0424sec
 1.08
 7 queries
 GZIP Disabled
Time is now: 19th December 2025 - 07:23 AM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.