Will do that

Bros...

Question.. does prodigy M needs come sort of a cooling system? since its consider a Small form factor im afraid the air flow will be bad...

If yes for cooling system..what are my options on those kind of system...budget will be around <500..

Prodigy M to my observation is offering good air flow due to it's design, from the above we can install 2 x 120mm fan blowing inward good for GC, at the rear the option of either 120mm or 140mm fan blowing to outside and the bottom 120mm up to 200mm blowing to the outside as well, but I've seen some put in blowing inside. Running at non oc the original setup just enough imo. Unless you want to have some aesthetic looking plus performance, AIO is another option to have it, but the the cooling performance may vary depending of model.

Powerwoot is correct.. not too much of a cooling system just making sure that the fans are blowing at the correct flow

hi all !!

Im using prodigy case ..can i know how do i connect the 2x fan LED pin ? I Dont have extra connector already..my case just the front big fan running without LED only..

Hi and welcome to the tribe but I don't know of any separate pins for the LEDs by default.. any pictures to show?

The FAN LED i connect to the 2 pin socket but i use 1 pin only..

Note : Now the Front Big fan is running process with LED ..
But i have to ask..is it im doing correct ?

Have another 120mm no work since dont have FAN socket already

This post has been edited by ayu: Nov 17 2014, 04:25 PM


Attached thumbnail(s)

I believe you need some cable adapter like this https://forum.lowyat.net/topic/2109790

yes..i need a cable like this..Thanks your link !

to those of you in Klang

https://www.facebook.com/BitfenixMsia/posts/337376036441633

Nothing to do...try cut the side panel and ugly like shit...





Attached thumbnail(s)

don't give up!! need to fix that cable management that's all

wait my another side panel coming first then i will change the PSU to modular.
i will try make it as nice...thanks !!

Bro..share your case , i want to see how to mod like prefect pretty

what tool are you using? to have a straight cut dremel can do it but not as straight as using motorized jigsaw. I have both btw. And lastly use flat file to flatten any rough edge.

hahaha...i m using jigsaw cut direct ..hahahahaha dont have any tools..
wakakaka

Lol now I am running without chassis bro lolz swap too often for testing

Yes !! I'm feel so happy because i ordered a U-Rubber from topazzatech
If not ,without a rubber that was a Ugly side panel ! Now it look is nice ~~~~ ( But next time will buy a tools )

How ever, i will try to install a Custom Water cooling on this case..Will try update here when i get it .
( Dont know want to go for water cooling or not...want to find a cheap set )


Attached thumbnail(s)

Temporary cable management .......


can i know is it need a MODULAR PSU only can hide a cable with nice ???
I always stuck in cable step...anyone can show a Own Bitfenix Prodigy cable management ?


Attached thumbnail(s)

the window's looking Baller!! very nice... cable management is another story, ppl normally tuck the excess beside the PSU... you can get a custom PSU bay cover made from Mod'n'Go

like so-> https://www.facebook.com/Mod.n.Go.Design/po...315734265242165

Just now only received my side panel ..and XSPC radiator which bought from forummer ..I have to install water cooling 1st or buy the PSU 1st ? Want to know something here
is it all PSU can support the water cooling ? Just scare no enough power..haha i'm new to water cooling ...
Still waiting my pump and block ...

This post has been edited by ayu: Dec 1 2014, 02:08 PM


Attached thumbnail(s)