If you're using the VoIP or IPTV, you wouldn't be able to change your router unless you are familiar with network configuration. I would recommend using a powerline or if your house is on three phase wiring, you have no choice but to use an extender.

If you're not using VoIP or IPTV, I would recommend changing to a TP Link router if you are on a budget or an Asus router if you have a higher budget.

got it. thanks sifus!

this router cannot use multi tagging vlan so cannot use more than 2 vlan on 1 wan port

use internet cannot voip, use voip cannot internet

i prefer this page: https://klseet.com/52-isp-a-telco/p1/p1-gen...-dvg-n5412sp-a1

this is my setup, custom router for internet only and, share 1 more LAN port to thosmas router for voip only


This post has been edited by delaciox: Sep 11 2017, 10:07 PM

Repeated POST, pls admin delete

This post has been edited by delaciox: Sep 11 2017, 10:08 PM

whats maxis fibre MTU?
vlan 621 for internet YES?
Need not the voip

Try 1480 or 1492 for the MTU. VLAN is 621 for Internet.

thanks it worked

i used xiaomi router pro + tplink smart switch combo

refer - https://forum.lowyat.net/topic/4262597/

Take note on those who are using Dlink router.
http://www.soyacincau.com/2017/09/19/d-lin...unifi-wireless/

hi all, I relieased my Vlan id for internet is 11, not 621. Know what is the reason?

Wow, thanks for the sharing.
Been using VLAN ID 621 all the while, and normally I have public address of 121.122.XXX.XXX.
After using VLAN ID of 11, I have public address of 14.192.XXX.XXX

Other than IP address change, I am not sure what else is different.

Edit:
It turns out that I did not applied the settings for modified VLAN ID, using VLAN ID of 11 does not get me connected to internet.

This post has been edited by alexander3133: Sep 21 2017, 06:55 PM

That is weird le, I use 621 then it don let me connect T_T
Im also in public address. And yes, my ip is 14.192.xxxxxxxx

Are you on Maxis infrastructure?

how to know if im in?

My Current Setup:
Service Provider: Maxis Home Fibre Internet
Modem: ONU-HUAWEI-HG8240w
Router: Synology Router RT1900ac (with Maxis VoIP setting enabled See Here!)
Phone: Normal Landline Phone

Can I use a RJ11 to RJ45 cable to connect the router and the normal landline phone? Will it work?

This post has been edited by aftersix: Oct 8 2017, 12:21 AM

Don't think so.
Based on your setup, you are using router without VOIP function (no RJ11 port).
Your VOIP phone is a device using RJ45 port from router.

Then what should I do to make my landline phone work again? Need advise from sifu.

You can used back the original router from Maxis, it c/w RJ11 port.
Or you can buy another router c/w RJ11 port. (VOIP support)

My old Maxis Router Thomson TG784n start working abnormal and connection keep on dropping and frequent restart require.

I contacted Maxis Helpline, said if WIFI router faulty can replace for free. Anyone experience free replacement even out of warranty.

Not sure how much I can trust them.

If they say that, make sure you ask the if you need to renew your contract or any other stipulations. However, if you're not using VoIP or IPTV, just get your own router and set it up.

Too bad I'm using VoIP which the router hard to find ... let see the investigation outcome.

Hope for the best...

This post has been edited by conqu3ror: Oct 15 2017, 08:12 PM