i have this wireless drill/screw driver ... drill

and thinking of getting this ... drill bit but don't know where to get...

to drill es'tile porcelain tiles in kitchen wall...

what do you think?

i am pretty sure u cant drill tiles using that drill. U need a drill with power souce . Or else its not strong enough.

but the guide states can drill metal ...

first get a punch tool...

then any mason drill bit is fine..

katijar, both item can get at local hardware shop that carries bosch power tool. that is the correct bit for tiles. 6mm is around rm16 and 8mm is around rm18 if i am not mistaken. its better to get corded drill instead of the cordless one. after you drill the tiles you need to change to masonry drill to continue drilling in. do not used the tiles bit, very fast will kaput.

i have drilled lots of tiles in bathroom to fix handle bars..

no issue, just mark or punch tile (so drill bit wont slip_

then use regular normal concrete bit...

http://en.wikipedia.org/wiki/Punch_(tool)

Central

File:Punch (central).jpg
A center punch
A central punch is used to mark the center of a point. It is usually used to mark the center of a hole when drilling holes. A drill bit has the tendency to "wander" if it does not start in a recess. A center punch forms a large enough dimple to "guide" the tip of the drill bit.[1] When drilling larger holes, and the web of the drill is wider than the indentation produced by a center punch, the drilling of a pilot hole is usually needed.
An automatic center punch operates without the need for a hammer.

i've drilled tile using wireless drill but u hav to use little bit extra force to drill it...i didnt use that drill bit, i just use drill bit that meant to drill through concrete

how to use the punch? hammer it?

---

Added on May 11, 2012, 2:29 pmtiles on the wall?

This post has been edited by katijar: May 11 2012, 02:29 PM

yes

thanks, i already has the cordless drill... if i have to get a new one i will just pay someone to do it...

---

Added on May 11, 2012, 2:31 pmdrill slowly? tiles no crack?

This post has been edited by katijar: May 11 2012, 02:31 PM

if u use wireless drill u have make a little chip by hammering screw on the tile just a small "titik" as the tile will be slippery if u dont do this....then u have to use the full power of the drill with extra force pushing through the tile...i've also used wired drill to drill through tile n it is easier...

Use masking tape will do also. If you don't have puncher.

hi, are u all the "pro" or normal DIY people?

normal diy

ok... thanks for the replies.

TS mention porcelain tiles not ceramic tiles, the bosch wireless driil may be can drill 2 holes before the battery flat or the amature burn

don't use rotary hammer drill / masony drill as u don't want your wall tiles become hollow.... my 1x2 porcelain tiles above basin counter all hollow now because the basin counter guy hantam with masony drill

How would a rotary hammer drill cause your tiles to become hollow?
That would be more of a tiler problem, your tiles did not become hollow they merely did not grab onto the surface you are trying to stick it on with enough grip. If you pull out the tile you can actually see cement sticking onto the back of your tile but did not stick onto the surface it is supposed to stick on. Normally when tilers try to tile a slippery/smooth surface they apply a later of coating before they paste tiles on with cement.

To the OP you can definitely drill holes on tiles with a cordless drill because I just did it last week, but like skng said drilled like 2 holes full battery already finish. You can use plugged in rotary hammer drill too but have to start slowly slowly then only increase speed. If you straight away go max power and drill of course your tiles would become ruined before you manage to drill a hole, hope this helps!

Your tiller did not put enough cement. Some area do bound to have some hollow, knock on the tiles, of no hollow sound than is ok

1. never use hammer mode if your drill support it...
2. drill slow... and consistant with some pressure pressing...
3. stop after a few minutes..
4. yes it takes time to drill...
5. fast /press to hard = cracked tiles
6. after drill through the tile change to normal bit to drill through the concrete behind the tile can use hammer mode..

wan drill fast get a diamond bit that is designed to drill through tiles/ceramic/porcelin and all that stuff

No only cement but tile adheisive +cement + susu....before laying tiles,apply thin layer of susu+tile adheisove, lay tile use opc +tiles adheisive+ susu as manufactural recommandation :nod

Porcelin tiles look nice but really give me problem.....out of my 10 project, 9 having this problem after worker drill tiles to install fitting:(

This is the correct way to drill tiles