Alright, order placed.

Keep your fingers crossed now

And wait

Preparing for Bulk #2 once this bulk finishes

Any tentative stuff you guys want?

if not mistaken it is bms-631mg hs servo.

http://www.hobbyking.com/hobbyking/store/_..._10sec_46g.html

Maybe I'll order power supply next bulk..

charger too?

saw the new r31 linked rear suspension set, do you really need that much traction at the rear?

Just asking, how long do you take to be able to do donut nicely...?

guys... i just got myself speed mind 64p spur and pinion... is this brand ok?? i never heard, i just try buy coz the seller said ok... lol..

Come guys..

What else you guys want for second bulk?

Charger i hv.. Rite now using power adapter.. Current not constant..

Where? Any pic?

Depends.. It took me about a month..

Speedmind is good.. Where did u bought it? Wanna buy also.. Their spur is flat unlike other got some fancy holes..

ni bro
http://banzaihobby.com/index.php?main_page...oducts_id=13462

i bought it at Time Square, Graffity Hobby at 6th floor, in front of escalator... good to hear it is good..

wow, nice and sturdy looking design, is this really important??

it says can give camber adjustment on the fly, as and when your damper changes.
so you will always have traction exiting corner. not sure if it's practical in RC anyway. wait till there's a user review. haha

oooo~~ sounds promising...

My swing shaft broke. Should I replace with this
http://www.myrcstation.com/webshaper/store...roductItem=6182
or
http://www.myrcstation.com/webshaper/store...roductItem=4249
which is better?
and also, there is 2 thickness 51mm and 48mm. Which is better?

---

Added on June 15, 2012, 11:02 pmor this (this is cheaper)
http://www.myrcstation.com/webshaper/store...roductItem=5371

This post has been edited by sphiroth: Jun 15 2012, 11:02 PM

front UJ is 48mm, rear can use 51mm

if you're free at night tonite, go to MRC puchong, ask for fijon UJ. as good if not better than eagle racing. look for Wong there... not sure if have stock, but worth a shot.


eh wait you're not in klang valley rite?
then take the eagle racing.
my advice, get a rim with at least 5mm offset. better if can get 9mm offset. pair with 200mm body. clone kit have tendency to rattle a lot on the front wheel, UJ easier to broke. just from my experience. without offset the rim very close to your c-hub when turning and sometimes it brush each other

This post has been edited by ayiesz: Jun 16 2012, 10:10 AM

The eagle racing (http://www.myrcstation.com/webshaper/store/viewProd.asp?pkProductItem=6182) is 51mm. Should be ok right?

if rear then can take 51mm. front i'm afraid it will be too tight, that is if it can fit it.
try to find fijon

Here not much choice..actually. don't know whether got stock or not. Furthermore, R31 is new thus most people use 416 which cause shop didn't keep parts for R31.

---

Added on June 16, 2012, 11:55 amAnd its for the front

---

Added on June 16, 2012, 1:44 pmJust done some checking, the 'drive pulley' (i think whats it called) teeth kinda worn out. Should be replaced with this right (the same 18T). Want to order as spares since i read on the net the standard one will definitely breaks after some time.
http://www.myrcstation.com/webshaper/store...roductItem=6386

Sorry for too many question...i'm a newbie.

This post has been edited by sphiroth: Jun 17 2012, 01:33 PM