i custom made blok kat taiwan .. factory is at china .....

head ah .. i will go check it out at sat .... not sure apa size .. scare buy wrong jer ...

You got ask they custom the block longkang bo? made it like semi open longkang. Like this better. Less leaking problem. Estimate howmuch u spend for the block arr? And what material??

---

Added on March 21, 2012, 1:40 amWant play jek rod must be very careful with compression ratio. Don't set too high compression, later your kaki and the engine lingkup.

This post has been edited by TryX: Mar 21 2012, 01:40 AM

nanti nid to spin tayar to start kick also susah xD

Agree +1

---

Added on March 21, 2012, 9:40 am@Tim...ask utm or maju motor sin b4 u bought the head...head is expensive u know???

This post has been edited by 163119779: Mar 21 2012, 09:40 AM

Asked kecil advice .. Jack rod ft big head valve ...
Head around 500 can cari 1 liao ...

The blok cost murah but shipment kos killing me and need at least get 10 biji baru murah ... It is a fast cooling material .... Piston is forged 1 ....

But sudenlly turun engine just to convert es ... Feel very wasted lah ...

This post has been edited by thianz: Mar 21 2012, 09:54 AM

This post has been edited by alexei: May 8 2012, 03:19 PM

guys, which one is the best btw CASTROL POWER1 or MOTUL 5100?

No waste la...Change ur main bearing to heavy duty bearings...Forget racing bearing...Plus check the road and condition of engine parts la...if possible..this saturday plan to buy 2 main bearings and TKRJ rod. And asking which part are make the sounds like this.. XD
@Tim.. So ur taiwan block project needs to be stop?

Maju motor got sell new head for about 500+ can get la....

Tim need big valve head la...Ya lor...tim...use current head first....wait uma big valve head come out the straight use UMA 1 la...but expensive a bit and dunno uma when launched it.
@Bro eric...how much do charge if overhaul engine in maju ??? I bring my own road and bearings..

This post has been edited by 163119779: Mar 21 2012, 11:03 AM

sorry forgot to mention big,this 1 is big valve la, bore up from indonesia, 19/22, IINM....

standard size cost less la, 300++ oni la....

Oo....ori head expensive la...last time i saw a guy buy new head for his lc..empty head cost Rm500++...><

I do not know u ask yourself, certain things u buy from them and include installation cheaper than u buy and bring over for installation....u just need order from them....U have not ask from them, how u know they can get for you....

They style not like UTM, anything also dun hav....

U r not going to save a lot....

---

Added on March 21, 2012, 11:10 amu buy 500+, then better buy the bore up version, using ori block to bore up...

where he buy? i got offer from them....too bad ur fren buy 500+ for standard size head....


This post has been edited by NewGUY: Mar 21 2012, 11:10 AM

No la...if i overhaul just check the engine and clean the engine up only...well...maybe change bearing to heavy duty 1 and change the rod to tkrj rod.

---

Added on March 21, 2012, 11:55 amI don't know la...i go workshop for tighten my chain...1 foreman bring a new head to install in lc cause the head was failure to modify by someone...Well...he told me that the head cost Rm500...I don't know he got con or what la...It just empty head. Cause i didn't plan to overhaul right now...and the parts just buy in case i need to overhaul..Bearing and rods only..I think not more than Rm180 if cash and carry gua...

This post has been edited by 163119779: Mar 21 2012, 11:55 AM

Which one is Fully Synthetic.

Bro eric....if overhaul + TKRJ rod + Fz blcok + fz cam how much ya? XD Just curious to ask ..XD

i dont know, I m not boss, u call him la, u got his no....

Number lost already... But i just need to know overhaul how much only...>< And need how many times to done ....Else i maybe pass my bike to utm overhaul...

this maju motor.. mana place pnya kedai ni?