KL one i dunno lah.. But u can bid for the plates lah..

Yeah corright.. haha.. Nope changing the extractor wont help u save oil.. It helps u save petrol.. haha..
Generally changing an extractor gives u the benefit of unlocking HP from ur car that is restricted due to the catalytic converter in the car a.k.a catcon..
A good extractor can give an improvement of around 8-10whp.. A catcon delete can give u at least 4whp increase in HP.. So u get better FC at the same time cos ur car is more powerful and u dont need to rev so hard..

Cos without catcon we are polluting the environment a lot.. They have sports catcon also.. Lesser flow restriction but still got catcon..
Technically most of the ppl that buy a car do not modify their car.. Most of them are car savvy only or youngsters are the ones that modify the car..
Most of the developed country do not allow u to remove the catcon..
Some countries like singapore u cant even modify ur engine.. haha..

Save the environment mah.. Not all cars decat ady sure save petrol.. Really modern cars with all the new tech and gadgets actually are optimally tuned to save petrol no matter with the catcon on or off..

Hehe no probs.. We are still awaiting the first turbocharged Persona in our club..

Can die loh like that..

nope.. the 20/12/2012 is caused by the mayans who got lazy and stopped drawing their calendar on a slab of rock..

yeah lah. thats y sometimes think that hotbits setup is cacated.. BUt then also the setup provides very good power.. Really cant understand..

I think u forget NO can kill ppl very easily even in small concentration.. Its odourless but terribly deadly..
Yeah it damages the environment.. But there are enough celebrities driving prius-es to help negate my damages.. haha.

LOL.. then recommend everyone to go drive a CR-Z ... 4.4L/100km FC.. Then we all can go and speed around..

That one need samwong to post a pic..
Sam take a pic of the extractor and post it here.. we want to see is it the same combination as this..

I think drex no more masuk stock for Hotbits ady lor.. Now he full fledged FGK supporter ady.. haha..

Powerzone only can get from the Powerzone shop lah..

FGK lah.. haha..

Nope.. So far only 4-1..

Hi welcome.. Ur car is B line or M line?
Yeah i got install that Locktact..

Oit thanks..

Except for the finishing and piping diameters and primary pipe length, not much difference.. haha..

CR-Z very small lah.. Drop by a Honda showroom to see the car first..

Yeah.. So faster go get a LCP..
Tell ur kids to study hard.. Get good grades then can apply scholarship no need to burden parents so much..
But now they are 10yo only.. Later when they are 18 or 21 time all will change in thinking.. Want to become businessman next time..

Msia they bring in the 4 seater one..

1,3,4,2.. Thats the PE firing sequence..

LOL 18yo want to marry means u never teach him how to be cheongster ady.. Then later parenting fail..
His shop is in Bukit Jalil Esplanade.. Very near TPM there..
HIs fesbuk..https://www.facebook.com/drexchan
Installation normally take less than 20mins lah.. He damn pro sure can change damn fast..

This post has been edited by ZenGTMM: Jan 30 2012, 04:53 PM

Ori weight is 1.9kg..
LCP weight can never be below 1/3 of the ori weight, if not surely got problem such as crankshaft unblaanced etc..
Myth weight is 600 something gram, works is 632grams..
Myth is teeny weeny bit undersized, works is same sized.. Both also wont create any bad effect..
If u take like redline LCP then no really much improvements.. Cos its 900+ grams.. Not much weight savings..

Lighter LCP wont cause problem with ur crankshaft twisting..
The only problem is it will cause harmonic resonance at a lower RPM if ur engine is turbocharged..
IF u really want a super good crankshaft u can buy a new crankshaft used by the CFE engine and put it in our car.. 1.5k only.. Fully forged crankshaft.

Everybody come join for TT loh..

hehe thanks.. Gong xi going xi.. Ang pow ada?

Not sure.. Mb this weekend will have one.. Where are u staying?

LOL u rarely drop by here mah.. And u are still the only member we have from Terengganu..

haha.. Y lah Persona very rare in Terengganu isit?

See mb this weekend loh..

TT means teh tarik.. T.T means crying face.. haha..

Adding a bullet helps to compress the air and add backpressure.. When u add back pressure u are maintaining the compression of the engine combustion, which is very important .. When u add back pressure u actually reduce a bit of pickup.. cos when u accelerate ur exhaust velocity becomes faster, but the bullet and s-flow is restricting the airflow a bit by compressing it.. Thats y removing a catcon can improve pickup and low end power..

But then backpressure is still needed.. Thats y auto gear cars need to have s-flow mufflers.. It helps maintain a certain amount of backpressure and exhaust velocity, therefore maintaining compression in the engine.. If u lose compression in ur engine u actually will damage the engine due to the engine burning either too rich or lean..

Theoretically no.. With a firing sequence of 1,3,4,2.. THe air technically clashes when the 1st and 3rd chamber are fired consecutively, then the 4th and 2nd chamber are fired.. But then in a 4-2-1, scavenging effect from a well tuned extractor actually helps to pump the exhaust air out, therefore increasing exhaust velocity and giving much better pickup.. But the problem is each extractor is only tuned to operate at a certain RPM.. FOr example hotbits may be tuned for max scavenging effect at 3.5k RPM.. So the pickup will generally improve until 3.5k rpm.. after that the effect is not as good as a extractor tuned for 5k rpm.. etc..

depends on the scratch and dent.. The dent the bigger it is the more expensive.. Scratches generally no matter how many or how deep on the door, when u repaint u actually repaint the whole door.. Therefore it cost the same to repaint with 1 quite deep scratch or 10 very deep scratches. .

A midbox creates multiple air distortions in different directions, therefore muffling down the exhaust gas sound.. It does create slight amount of backpressure too..

FINAL DESTINATION!

Know ur car better.. Push it beyond its limits, then only u will know what is ur car limit.. U will never know the limit of ur car if u never push it beyond the boundaries!! hahahahaha..

Hmmm Since u say the wira ady 18yo.. I suggest doing other things first lah.. How much is the mileage?
First u need to decarbonise the engine. Run a decarboniser to remove all those soots..
Then its good time for u to do a minor top overhaul.. Just change piston rings and clean the engine head will do..
After that check for compression problems.. No matter how good ur exhaust is, if ur compression got problem and u install a bullet or midbox to increase compression, u are going to cause a lot of piston blow-by.. After that clean ur throttle body, and change a new filter.. I think these itself will cause u quite some money around RM1k ady..

Walau money printing company wei!!

I got Sliverstone NS500 Kruizer 1 with my B line PE leh.. Ok lah quite good.. Dry road grip is above expectation.. Wet grip is not that good.. Can aquaplane easily under heavy rain at low speed.. But light to moderate rain can go high speed easily..

He LPPL a lot lah.. That fella using Powerzone.. Drag car wei..
Eh samwong when u free? I need to drag u this time leh.. Lets see which car is more powerful..

Our engine rev cut is at 7250.. So no worries.. But dont always high drag ur car like that lah.. If not u will be changing a new engine every 2years. haha..

Lotus Handling.. U can really push the car a lot.. Thats y i say try to push ur car as hard as u can (in a safe place of cos).. When the car surpass its limits then u will know the limit of ur car..

How bout changing a short shifter into ur car and powershift at the same time? U barely lose power or momentum..

Give u a list to mod lah..
1) Works Engineering Drop-In Air Filter - RM120
2) Denso Iridium Spark Plugs IT20 - RM160
3) Works Engineering Lightened Crank Pulley - RM360
4) Grounding Cable - RM50-80 (get it from erictioh)
5) RaceTech Chassis Alignment Kit - RM200 (if u want really good handling and comfort)
6) HotBits Extractor 4-2-1 Long primary - RM580, u can get cap ayam if u are not rich enough for this..
7) do up ur whole exhaust if got money.
8) Port and Polish ur engine head. A simple PnP will be quite sufficient. Cost around RM500+. Professional ones cost around 1.5k, with benchflow testing..
Those are the basic mods u can do to increase power lah.. Those i mentioned a newbie level mods.. When u go to amateur level u can touch throttle body boring, crankshaft balancing, engine blueprinting, hi-cam etc etc.. As long as u got the money i got the parts to recommend u to change.. hahaha..

Whats ur fb name ah?
THis is our official fb group..
https://www.facebook.com/groups/LynPersonaClub/

Me.. Install in JB.. RM250 only..

It depends lah.. Easy way for u to calculate is to take the loan amount, times by the interest rate and divide by the months u are planning to pay..
FOr example u want to take 55k loan at 3% a year for 7 years. take 7 years times 3% = 21%... 55k times 121% = RM66550.. THen RM66550 divide by 84mths = RM792 a mth..

Die means die together!! Kill all the turtles!

This post has been edited by ZenGTMM: Feb 1 2012, 03:23 AM

Hmm have to tune using the EQ lah..
K.Lee sure laughing now.. Sony HU all are bass loving type..

Illegal only if u get caught.. hehe.. I got see popular selling the portable HDD b4..
haha hvnt go find KC yet.. My friend got open car wash and detailing centre in JB.. So i paid him 10bucks, and he cuci and polished up my car for me.. So now no scratches at all.. Just the slight dent only.. and the broken side mirror..

Rev cut will kick in and u will suddenly lose power..
cable is to improve grounding for ur car.. So ur audio would be very clearer and more bassy, aircon will be cooler and slightly faster gear change.

hehe.. Clean all the holes! lol..

Yeah u can.. Normally ppl use Evo3 brake kit. Cost around RM600 for the rear only excluding lower arm and installation..
If u want to change full set including front disc with twin pot brakes and brake pump servo also will cost u around 1.3k-1.5k excluding installation.
Normally the best fit is Evo 3 brake set lah..

So expensive.. Just go drex there get the Rapid Stop one.. The best road using pads so far and only cost RM160..Not even bendix can come close to this one.

---

Added on February 1, 2012, 3:18 pmLOL bro dont worry bout that.. haha.. If they blame ur brake pads its time for u to shoot time nicely..
Brake pads wont affect engine health..

This post has been edited by ZenGTMM: Feb 1 2012, 03:21 PM