AMD X2 Overclock, will this help?
|
|
 Jun 1 2007, 11:17 AM
Return to original view | Post
#21
|
 
Elite
8,103 posts Joined: Jan 2003 From: Tanah Lot @ Dungun, Terengganu.  
|
QUOTE(gsan @ Jun 1 2007, 10:34 AM) 1-3'c yas one doesn't count, cheatin one...     how u guys reduce d temp of pwmic? i found that it's freakin hot, d temp is proportional to d amount of voltage pumped to d chip...  60'C of pwmic temp is abit too much for me, considerin i only applied 1.325v of vcore, imagine if i put 1.4v of vcore...  |
|
|
|
|
|
Jun 6 2007, 09:15 PM
Return to original view | Post
#22
|
|
Elite
8,103 posts Joined: Jan 2003 From: Tanah Lot @ Dungun, Terengganu.
|
guys, need some help here... wat cud be d reason (in particular) of system freeze after primin for hours? my system is stable when prime with small fft (8-512K), but when i run blend test, freeze happened.
i admit that expert is harder to tame if compared to ultra-d, but there must be a way, just short of time to find out what is d culprit as i'm busy w job huntin lately... ram settings, ldt voltage, chipset voltage or vdimm? i notice that expert needs more juice than ultra-d or nf4-d. still my nf4-d is d best of all so far, but it's resided in my gf rig currently... 
This post has been edited by ah_khoo: Jun 6 2007, 09:18 PM |
|
|
Jun 7 2007, 07:35 AM
Return to original view | Post
#23
|
|
Elite
8,103 posts Joined: Jan 2003 From: Tanah Lot @ Dungun, Terengganu.
|
QUOTE(uzairi @ Jun 7 2007, 03:07 AM) It seems that all the voltages were at stock, increasing it might help i think. Especially the vChipset and vLDT and vCore. yup, i just increase d ldt voltage by one notch, mebe should try increasin d chipset voltage as well. nothing wrong w d vcore i guess since it passed small fft w/o problem, headache comes when ram is involved...  QUOTE(gsan @ Jun 7 2007, 03:13 AM) expert is for "expert" only yup, mebe am just an expert wanna be... ram setting could be the factor and it's more difficult to tweak compare with nf4 older series. btw, expert vdimm overvolt 0.01v or almost same as the value in bios unlike overvolt much in older nf4, that's why sometime it need higher vdimm. am tryin to burn it w/ memtest test currently, mebe d ram need time to settle in w d new mobo. too much option available in d bios for this expert, but am kinda like it even it's torturin me now... QUOTE(uzairi @ Jun 7 2007, 04:35 AM) I think what limits my x2 overclocking is the psu. I increase all the voltage also cannot go, errors at the 2 round most of the time. Time to get the fortron 700w.. am aimin ocz now but pocket empty, they just come out w new series lately if i'm not mistaken.   This post has been edited by ah_khoo: Jun 7 2007, 07:36 AM |
|
|
Jun 7 2007, 11:44 AM
Return to original view | Post
#24
|
|
Elite
8,103 posts Joined: Jan 2003 From: Tanah Lot @ Dungun, Terengganu.
|
QUOTE(gsan @ Jun 7 2007, 10:15 AM) the bios is almost same as nf4 series if I remember correctly, just the ds/dds option more advance. exactly... can't even boot up even i've tried to switch d position.  some tips for you, try the lowest value first, weak 1/ lvl 1 instead of auto and the yellow slot in expert mobo is "cacat" why dont go for corsair psu?   i'm usin lvl 14 now, so far memtest ok. odd no = weak while even = normal, d smaller d no. d weaker it is, rite gsan bro? auto wud be d strongest of normal if 'im not mistaken (wild guess only since it starts w 1 instead of 0). corsair modular psu? hmm... modular psu is not my cup of tea leh... |
|
|
Jun 7 2007, 12:49 PM
Return to original view | Post
#25
|
|
Elite
8,103 posts Joined: Jan 2003 From: Tanah Lot @ Dungun, Terengganu.
|
QUOTE(gsan @ Jun 7 2007, 12:10 PM) as I knoe, lvl 9 and above is for 4 dimm, but I never try before. you're right, odd=weak and even=normal. my bh5 can up to ds/dds 8/4 at 250MHz @ 2-2-2-5, any frequency above it have to tweak from the lowest value. if I not remember wrongly, OPB suggest that only set ds to lvl 1 then tweak around the dds from lvl 1. i see... shoud try ds = lvl 8 then. same here, i alwez use dds = lvl 4 for tight timin ram. i thought tight timin ram shud use normal, only tccd or high frequency modules use weak ds eg. lvl 1, 3, 5 or 7? hmm... will give it a try after i'm settled w gettin a new job, as for now, work is more important... |
| Change to: |  0.0199sec
 1.04
 7 queries
 GZIP Disabled
Time is now: 2nd December 2025 - 03:37 PM |
Quote