Opteron 939
|
|
 May 29 2006, 10:53 PM
Return to original view | Post
#1
|
 
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa   
|
QUOTE(kulus @ May 28 2006, 07:13 AM) i think it is 1.4v la..hehehe..cpuz reading always show lower from what we set in bios.. it not lower la , but more higher for some pc i think . because i set only 1.4x volt but cpu-z show 1.5volt   .use stock vcore i cannot prime more than 16 minutes , later pc will keep rebooting . maybe that because of my psu . see +12V , only 11.7xvolt   This post has been edited by xeratos_85: May 29 2006, 10:55 PM |
|
|
|
|
|
May 30 2006, 02:45 AM
Return to original view | Post
#2
|
|
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa
|
CAB1E <-- only this i remember . im too excited when receive this proc and forgot to see what wrote on proc . put thermalpaste and screw the waterblock than that time only remember that i not yet see what wrote on the proc
 .. so now dunno what week i got . |
|
|
May 30 2006, 08:56 PM
Return to original view | Post
#3
|
|
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa
|
maybe u not set HTT multiplier . now u use 5x right?try to change to 4x or 3x depend how high ur HTT .
|
|
|
May 30 2006, 10:02 PM
Return to original view | Post
#4
|
|
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa
|
the problem sure from bios setting not ram.. try to see where got setting for the ram . u use abit kn8sli?
|
|
|
May 30 2006, 10:20 PM
Return to original view | Post
#5
|
|
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa
|
QUOTE(crayzee @ May 30 2006, 10:09 PM) corsairs lousy chip ya la. .. i not familiar with abit socket 939 bios . my asus can set auto divider to find most suitable setting . did u try like using only 1 stick or try other ram? what setting in the bios i should tweak? i'm planning to run on (290X9) with 133 divider which means 2610Mhz and 386mhz ram. impossible cant post since i run the dividers the ram is running less than DDR400. Yes i am using kn8sli. The divider option kinda little 100,133,166,200,233,250 only  guess that my board is picky in dividers |
|
|
May 30 2006, 10:42 PM
Return to original view | Post
#6
|
|
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa
|
ur ram or proc not stable?maybe proc also cannot go that high. anyway , did u check ur ram voltage?
|
|
|
Jun 2 2006, 05:38 PM
Return to original view | Post
#7
|
|
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa
|
QUOTE(rzonealley @ May 31 2006, 08:37 PM) havent got chance to set up my system yet. what mobo u want to use with ur opty? all latest mainboard already can support opty with need to flash latest bios.the mobo n cpu still lying in my room... i just worried that the mobo cant run with the opteron. anyone using the same setup with my opti? |
|
|
Jun 2 2006, 10:26 PM
Return to original view | Post
#8
|
|
Senior Member
1,369 posts Joined: Oct 2005 From: Terengganu & Taman Shamelin Perkasa
|
QUOTE(satanhead2003 @ Jun 2 2006, 08:15 PM) well, here's mine doing 1:1 at 3G pc4000 ram , that y can go 3g with 1:1 ratio  lowest voltage i could run 3G, but this time hv to used divider  . me no momey to buy high performance ram  |
| Change to: |  0.0164sec
 0.72
 7 queries
 GZIP Disabled
Time is now: 10th December 2025 - 05:44 PM |
Quote