your knowledge on mechanical stuff is so good.

Sanden's factory to produce the compressor is in Pasir Gudang and I occasionally visit the production line.. The compressor assy will then be shipped to shah alam.

I back abong for number 1. that i see got 2 wire comeout for energize the magnet clutch of air-cond. compressor, but for no. 2. i don't dunno and i never see the internal assembly off compressor.

btw if really gear box hancur there should be more gear around lah.

This post has been edited by ngeo88: Nov 30 2011, 07:07 PM

Bro, additional info for no 2.. Our PE use this kind of compressor operation.. The gas air compressed by the pistons. Where else for other brand like Zenith & Calsonic, most of their compressor using rotary technology.. Rotary compressor compressed the gas better compared with pistons but need a lot of energy to turn it into operation and will consume a lot of torque generated from the engine.. Hence only bigger engine are practical using such operation.. Nissan with its zenith compressor use rotary in their skyline model from R32 until the recent gtr.
This piston is actually very small, it is between the size of 50cent & 20 cent only with rubber rings.

Oh ya, regarding the picture no 3, IF I'm not mistaken, it is the shaft located between the pistons base plate for the pistons and the magnetic clutch.. It looks the same, but I haven't see yet the inner parts for PE compressor.. Usually the gears are a lil bit straight compared with this one looks swirl..

Did u noticed when the a/c compressor kicks in, there's a sound produced at the compressor? The "klak" single sound.. This is when the thermostat give signal that the gas are getting warmer and need to cool it back.. This will then supply power to the compressor's clutch to engage.. The so-called planetary gears mentioned by Zeng will then be pushed to the baseplate to start the compressing process.. Just my 6cents

video explaned

Guys.. wanna further elaboration in 10k service

i have 2 option :

1. Use semi synt (petronas 800 10w 40) - will have to do own 15k service

2. Use full synt (i found in internet recommend petronas 3000 instead of 1000 - 5w 40) - maybe just need change oil filter for 15k service

What u recommend? as i said i will use d free voucher. so maybe will not buy other engine oil

better option 1 since you got free service why go spend money buy fully synth. oil. change oil frequen good for engine. even doing 15k service only using semi synth oil which is still cheaper than 10K km buy fully synth oil.

This post has been edited by ngeo88: Nov 30 2011, 09:22 PM

If let say i can get d petronas 3000 for free with d voucher (will ask cose tomorow), u think option 1 still better?

if synthium 3000 free then it was RM200 over then go for opt. 2 and give your review on using synthium 3000 here as not many member try using synthium 3000 before.

ok will phone cose tomorrow for conformation. coz from my reading petronas 1000 is better for protection but will make ur engine more heavy (thicker oil)

cos it was 15W-50, thicker oil better protection but heavy on acceleration.

@zeng, still can giv me better price for wegow 12" bullet?

hi.. i am back.. last magnatec, sold to my brother

One of our PE members punya..

Yeah.. Better tagline with safer info.. Maggi bring us nowhere..

30% off means how much ah? If say RM210 RRP then x 70% = RM147 per bottle is it?

Like ferrari mah.. When accident engine and front will disintegrate and let the cabin roll off..

Can.. 10-40 can stand high rev more than 5-30 engine oil..

Huhu.. I also dunno what the pistons were.. thats y i put the (I think bracket there).
As for the first pic I really thought it was a crank pulley lah.. It was broken off from the engine base where the crank pulley will normally be located. So thought itu Crank pulley.

Haha.. Got a lot more pieces around.. But all of it too oily.. So i didnt take it back.. Only these few parts were clean enough to be picked up..

d wegow 4-2-1 n hotbit 4-2-1 is different material rite?hotbit is stainless steel...wad bout wegow?n i notice that d configuration of dis 2 extractor is also different even though both are 4-2-1

Long story la

Wegow 4-2-1 made of galvanized steel. Honestly, it's a 'branded' cap ayam lah..

branded yet cap ayam...
tat day a malay dude installed d wegow 4-2-1...looks so yao yeng...but they try to find d stainless steel one on d rack in f1 shop but tarak jumpa...

Up for test drive... Anyone?

---

Added on November 30, 2011, 11:52 pm Troll them mah. Tell them urs wegow limited edition.

This post has been edited by xandras: Nov 30 2011, 11:52 PM

d colour variation is ugly...especially d skirtings...but d taillamp is nice if compared to d previous version...
interior got change?
troll them?they keep finding d brand of my extractor...i tink they end up still duno wad is d brand cz they ask d boss wad extractor brand is that but boss say i brought myself...so tarak tau...