EB x Medicom...... Ulimate Unision

Got EB's 1/4 Arnold...

RC fatboy... though a little larger almost to scale.... EB's Arnie stands 19" which translate to 6'4"(slightly overscale too).. with boot heels Arnie is around 6'2"(18.5").



This post has been edited by BeastX: Mar 7 2012, 07:57 PM

I'm sure there are Malaysians that have it directly sent from Hong Kong and will have it around a week..

how about u call them..... better knowing sooner rather than later...

Classic Predator: use pumbler's white tape to increase the ball of the neck.....

This post has been edited by BeastX: Mar 12 2012, 12:10 PM

Unpainted.... however some does have some over-sprayed paint on those parts.... Joints by its very nature for moving and rubbing of parts are not meant to be painted.



This post has been edited by BeastX: Mar 16 2012, 02:30 PM

HT's babydoll will do good with this:

Medi's RAH 583... Darth Maul:

HT... Hawkeye:

Inaccurate.... especially putting HT and EB in the same sentence.

repost:

There's a Mk. 7 on display at the fair/event:

Amber June
Babydoll May
Iron Monger September
DX Luke August
RedSkull July
Gantry July
Tron bike July
Avatar Jake June
Black Spidey April
Noland April.....

This post has been edited by BeastX: Mar 21 2012, 05:53 PM

Though expensive....

I'd say HotStuff female body is the best (well designed) female body for now.

http://www.infomax.co.jp/figure/hotstuff.html

Good points:
Bendy (thick wire) neck/shoulder/abdomen... full humanly possible. Well designed unidirectional joints flimsy looking, seems robust (elbow/knee/ankle/wrist)

Bad points:
Wrist only up/down side by side not available.
Ratchating/Rotating hips/shoulder are weak/fragile/limited range/limited positions...

Paint...

---

Added on March 24, 2012, 10:13 pmCloning:

---

Added on March 25, 2012, 1:10 pmLEAKING on a bat DX again...


It was always because of incompatible materials.... The suit is not actually rubber ..but PVC with very high plasticizers.... which is the liquid that leaks...

to avoid this make sure there's no contact between the PVC materials plastic between it will suffice.... Belt and suit

This post has been edited by BeastX: Mar 25 2012, 01:10 PM

Reissue Mark VI for Pepsi/7up contest in HK... Mk.6 with MechTest head


This post has been edited by BeastX: Mar 29 2012, 08:03 PM

Hot Toys - MMS172 - The Avengers: 1/6th scale Hawkeye Limited Edition Collectible Figurine
~ MMS Series ~
The 1/6th scale Hawkeye Limited Edition Collectible Figurine specially features:
- Authentic and detailed fully realized likeness of Jeremy Renner as Hawkeye/ Clint Barton in The Avengers movie
- Approximately 30 cm tall
- Muscular body with over 30 points of articulations
- Movie-accurate facial features with detailed wrinkles and skin texture
- Six (6) pieces of interchangeable palms with finger tabs on left palms
including:
- One (1) pair of relaxed palms
- One (1) right palm for holding bow
- Three (3) left palms of different styles for holding arrow
- Each piece of head sculpt is specially hand-painted

Costume:
- One (1) black and pale red vest
- One (1) pair of navy blue pants with belts on waist and thighs
- One (1) pair of black boots

Weapons:
- Two (2) bows including one (1) fully opened and one (1) with articulations
- Sixteen (16) arrows and eleven (11) arrowheads of different styles with quiver

Accessories:
- One (1) pair of sunglasses
- One (1) right armguard
- Figure stand with Hawkeye nameplate and the movie logo

Artists:
- Head Sculpted by K. A. Kim
- Head Painted by JC. Hong
- Head Art Directed by Yulli
**Prototype shown is not final, pending licensor approval
Release date: Q2-3, 2012
TM & © 2012 Marvel & Subs.
© 2012 Hot Toys Limited. All Rights Reserved.

Guaranteed to get below 500 then... from my supplier....