Outline ·
[ Standard ] ·
Linear+
Toilet Bowl problem, tanki fills up very slowly
|
TS@Adele
|
Nov 11 2011, 10:59 AM, updated 15y ago
|
|
Hi sifus and experts of houses out there,
I just installed my new toilet bowl, is called Serifite. After i flush, the water that flows back into the tank is soooooooooo slow, like very very slow. It takes like 10-15 mins to fill up the whole bowl before able to flush again.
Anyone knows how come like this..and any way to rectify the problem?
Thanks.
|
|
|
|
|
|
kucingfight
|
Nov 11 2011, 11:04 AM
|
Look at all my stars!!
|
i think there's a screw adjuster to adjust the water flow .. should be somewhere near the water inlet to the bowl
|
|
|
|
|
|
weikee
|
Nov 11 2011, 11:42 AM
|
|
How is the water pressure?
|
|
|
|
|
|
TS@Adele
|
Nov 11 2011, 11:51 AM
|
|
kucingfight, thanks! i'll check it out.
weikee: the water pressure is pretty bad, i guess due to rusty old pipes. If use the water at only "one place", then it's totally fine. But if u share water usage .. for eg. bath and kitchen, then the kitchen one will become super small.
Was thinking is it because when do renovation all the rustiness fell into the pipes causing it a bit blockage or something...hmm
but doesn't explain why water flow into the tank is so small..
|
|
|
|
|
|
weikee
|
Nov 11 2011, 12:00 PM
|
|
QUOTE(@Adele @ Nov 11 2011, 11:51 AM) kucingfight, thanks! i'll check it out. weikee: the water pressure is pretty bad, i guess due to rusty old pipes. If use the water at only "one place", then it's totally fine. But if u share water usage .. for eg. bath and kitchen, then the kitchen one will become super small. Was thinking is it because when do renovation all the rustiness fell into the pipes causing it a bit blockage or something...hmm but doesn't explain why water flow into the tank is so small.. If the pipe is old, should have change the pipe when renovating. You can try take out mechanism and wash maybe it help (as you suspect rust was build up) This post has been edited by weikee: Nov 11 2011, 12:01 PM
|
|
|
|
|
|
birain
|
Nov 11 2011, 12:31 PM
|
|
QUOTE(@Adele @ Nov 11 2011, 10:59 AM) Hi sifus and experts of houses out there, I just installed my new toilet bowl, is called Serifite. After i flush, the water that flows back into the tank is soooooooooo slow, like very very slow. It takes like 10-15 mins to fill up the whole bowl before able to flush again. Anyone knows how come like this..and any way to rectify the problem? Thanks. the rubber must have worn out and stuck there(where the water flows into the tank area). had this problem all the time,i normally grease it and it's back to normal.
|
|
|
|
|
|
kamion
|
Nov 11 2011, 12:46 PM
|
|
Yes, the filters are probably stuck with debris. I don't know about your particular tank filling system, but I was told by a friend of mine that his had 3 filters, and he had to take apart the thing in order to clean out all the filters.
|
|
|
|
|
|
Jo_da48
|
Nov 11 2011, 03:56 PM
|
|
1) Before you change the toilet bowl, are you facing this problem? 2) Have you check whether the stopcock have fully turn ON? as when replacing the toilet bowl, they will OFF it and may only turn on half itself 3) Open the toilet bowl tank cover and check, if not mistake that should have a control of water flow around the pipe area
Or is that any taps that link with the stopcock and is the water small or big?
|
|
|
|
|
|
TS@Adele
|
Nov 14 2011, 03:18 PM
|
|
thank you everyone for the help!!
it was rust build up and like you all suggested, open, wash then put back in, OK already. tanki fill up quite fast now. pheww!!
|
|
|
|
|