the thing is, the warm air persist
1st sign of problem is the driver side vent & driver side of centre vent gives out warm air, only the other 2 vents give out cold air
then after few days, all vents give out warm air
i dare say it's a problem, cause the AC button is on, the setting is set to face-blowing full, the recirculate button closed
this time it's been 2 months since the problem started again, never, not a moment, the aircon got cold air

sounds funny. i can think of only 2 scenarios now... maybe others can think of others but here goes:

1) the diverter for fresh air (which is normally warm) is jammed. this means the recirculating air switch could be on the blink.

OR

2) the panel itself (the one where you press for temperature, air flow diverting, etc.) needs to be looked at. maybe the dial for temperature has also gone on holiday and is stuck somehow in heater mode.

hope it helps.

This post has been edited by lowpro: Nov 14 2011, 09:30 AM

heya lowpro,

i went to the SC to check on this issue, however I realised that i can only get it check next week as they are fully occupied. My fault as i didnt make an appointment, but i was thinking they might attend to walk-in customers to service customers cars. But my issue was only detected ending of last week, too short a notice to book for an appointment on the weekend as i am working on the weekdays. Maybe once the new SC opens at Glenmerie they could accomodate walk in customers

---

Added on November 15, 2011, 11:04 amBtw does anyone know of any good Peugeot workshops in Subang Jaya/USJ area?

This post has been edited by MAD MAX: Nov 15 2011, 11:04 AM

afaik, they hv close to 20 appointments per day and walk-in is on first-come-first-served basis. not sure but i think they take in about 5 per day? so, hv to be early if u wanna do walk in. anyway, do call this number 03-55663600. it is the glenmarie number to make appointments. cheers!

Here are some interesting facts about the 308 Engine:-

http://distributionthp.free.fr/index.php?l...on_view_eng.php

http://www.etuners.gr/en/index.php?s=12&t=167

Affected model includes Peugeot 308 in it.
This usually comes when you receive "Depollution System Faulty" and usually above 30k mileage.

http://www.justanswer.com/peugeot/5crow-pe...ty-warning.html

Those current 308 owners out there, better get the SC to check this out before it spoils your piston head/Cam.

Hi sifus.

My 207 has this weird *thangk thangk* noise when i turn the steering. Worse still, I can feel like some dawai moving underneath the footrest. It's as if the turning of the steering is clashing with some dawai or metal wire and this dawai thing can be felt underneath my foot!

Help urgently advise

I think is the foot carpet that cause this thing. Try pull the foot carpet a bit to the back. Hope this help

why is Peugeot service very poor?

they don't treat customers well and not that professional.

everytime when go to the service centre, there will be customers shouting.

even if stuff that supposed to be under warranty they will try say "this one normal la, can't fix etc"

i think whoever who is managing the Peugeot aftersales service has a bad attitude.....



This post has been edited by MAD MAX: May 19 2012, 02:51 PM

If you go to the world 2nd largest car market ie the USA, you won't see Peugeot, Citroën, Renault, Alfa Romeo or Lancia on the road. There's only 1 model of Fiat that was recently sold there. Most coveted cars there are Japanese Lexus, Acura n Infiniti and Germans Mercedes n BMW. Volkswagen are also selling 8n droves there. Americans, Swedish and Koreans Kia n Hyundai cars are ordinary cars there. Since driving conditions in USA are tough, you would know that cars that can't made it there should no be bought anywhere else in the world.

The problem EP6 with crankcase ventilation.

Repair kit valve cover for Peugeot 308, 3008, 207 (A7) engine EP6
Membrane valve cover for Peugeot 308, 207 (A7) engine EP6
OEM 0248.Q5
new diaphragm valve for crankcase ventilation.
producer sells only cover entirely.
we produce membrane separately!

replacement is very easy, you need to remove the valve cover by prying it with a screwdriver.
remove the old and install the new membrane.
close the cover.

vanos-bmw.com/peugeot-ep6-membrane-valve-cover

I wanna ask. I'm currently near the end of my extended warranty. Bought my 207 in 2012and it came with the 3 + 2 extended warranty. Now it seems there's some issue with my mounting but they tell me it's not covered by my warranty. Anyone can tell me if that's the case?

mounting are wear and tear parts hence not covered under warranty

Anyone had issue with their 208? It shows ESP/ASR system fault. SC quoted me RM1.5k to repair it and said it's not covered under warranty. It's not even a wear & tear part. Why is it not covered?

2017 going to 2018, its Peugeot SC still that bad?..

Thinking getting the new 3008 and the nearest SC for me its at Jalan 222 there.

Interested to know as well. Seriously considering a Traveller, but upon listening to the horror story, I'm not keen. One thing for sure, the 2 Peugeot showrooms I've been the SA are either lazy, not knowledgeable or don't give a rats ass about selling. I can't imaging what happen when the service technician works on the vehicle.

The new 3008 is good. Got for it, previous engine issues solved.

In 2012 PSA introduced EP6CDTM on 408thp in Malaysia. This engine carries 8 mods addressing reliability issues on the older Prince. As a result of its sucess, PSA provided this engine option on Citroen/Peugeot Sedan/hatchback/SUV/MPV . The new 3008 has a further refined Prince - EP6FDTM.

Dont listen to Uncle/aunty say, they dont own one, all hear say! I own one and am on the 6th year on EP6CDTM, no issues, running very well!

This post has been edited by SKYjack: Feb 10 2018, 12:12 PM

how long you have driven the New Peugeot 3008 new Model?