MY case?
Thank you Just want to share for that, I'm learning cable management by reading this thread also. Everyday take out the panel watch those cacing and try do something.

Now want to try on my GF casing, see what can do for that. I just use the zip tie to tie all those power cable for nice abit. Now planning how to hide again XD.

This post has been edited by vincent09: May 24 2007, 09:01 AM

jolipoli81 I also not so brave to sleeve those cable so i use zip tie to tie it all XD.

treason, after i mob i will cry for that XD. Now that casing ok already but now i get a case fand with controller, so have to challange again, else just leave it full speed.....2800++ rpm u know how noisy is there XD. ( Now i using heat sensor let it auto run the speed and feel better.)

Em i feel quite hot airflow come out from side panel ( close to GC ).
And if afternoon hot, my room also quite hot. GC temp can go to 60ºC++. CPU is around 50ºC ++ if not wrong.

Now let the fan sensor and auto change fan speed is around 1400 rpm. Need to test afternoon how was it. If no choice then use back that fan's controler to control.

Now the problem is don't know where to put my fan sensor, now 1 hanging around GC's top, another 1 is hanging motherboard power cable ( 24pin ).

This post has been edited by vincent09: May 25 2007, 01:26 AM

L shaped sata cable is it the the connector is L shape ? If is that i put that connector on my HDD the other 1 ( without L shape ) is connect to motherboard. Improving cable management? Maybe if you got more than 1 HDD and need to hide cable. For me i hide my SATA cable near the fan, so i need to avoid the cable attack by fan then use that L shape connector to make that cable not so close to fan.

If near the fan, for safety, i recomand u get some of it, But my L shape connector cable is come by motherboard. So is enought to use for me, now i'm using 2 SATA HDD and quite ok to manage the cable.

Upcoming Hardwares
Remember post a picture here akachester

This post has been edited by vincent09: May 27 2007, 01:45 PM

I feel my pc-60 more hard to manage because of the motherboard bottom there no hole to let all cable hide behind.

Wow very clean leh XD. Hmm try think for that for my gf casing ... Many cacing there until now T-T.

Maybe need to know what hardware got inside that casing, less hardware less cacing XD. If not wrong just got 1 HDD right?

Discrucio Anima, I'm not sure is it work for your or not. About the IDE, u can use another slot which is upper there then u can make the IDE short and hide behind there.
Sorry bro, is it the upper 1 is for Floopy or IDE ? If for floopy then is my mistake XD.

This post has been edited by vincent09: Jun 3 2007, 01:35 PM

Hmm my Lian Li pc-60 plus no place can go through behind mobo tray because totally close all area, then got other place to hide real fan if connect to front control panel?

I just think stick it on top of casing only ... XD.

PCIE cable, i don't know work or not, akachester is it u using Lian Li pc-7
? I don't know the PCI-E cable enought u to hide through behind the HDD case and come out from middle of the HDD case there. My case can't XD because no space at the back.

Doom ah, can i ask the real fan is it for intake ( i c website is like that ), but is it enought to blow in until front panel there? Or is it ok for cooling?

Don't know can get the anti vibration ring for accessory or not XD.

This post has been edited by vincent09: Jun 10 2007, 09:52 PM

Hmm i can't c the intake fan in front there. XD.
Anywhere no problem then ok la XD look like quite nice casing.

Vantec Vibration absorption kit ? hmm go check for that XD.

Doom, actually where is Jalan Pasar? Look like many ppl getting staff from there for modding or sleeve.

I see, maybe i look around there if pass by Time Square. Thank you DOOM for the info.


This post has been edited by vincent09: Jul 24 2007, 01:05 PM

Wasai mADmAN, your GC power cable and motherboard power cable manage so nice, I'm facing these 2 cable problem for my cable management. I can't hide my all powercable behind the motherboard tray because of hold to let me turn to behind, all flat planel there T-T.

OK mADmAN, here is my front & back view for my Mobo.
See what can do with the GC & Mobo power cable

I just leave for few month like that.







This post has been edited by vincent09: Jul 29 2007, 07:42 PM

Ya Doom, maybe i will get the Sata Burner soon because of my burner now start crazy, press it also don't come out. Still expensive now?
My burner now is stick on 3rd bay there, so those cable all is put at top there.


For my pc hardware spec >
Lian Li pc-60a
1 normal dvd burner
7900gs GC
2 Sata HDD
Acbel 450w power box
( Man, after buy the power box then i only know got some power box is with sleeve and can unplug, nice for cable management )

But mADmAN i feel your GC power cable quite long can turn and hiding at back.
I saw some of picture is showing that the Mobo power cable can fold in to L shape from mobo slot there like mADmAN but for me i feel can't because not so easy fold.

This post has been edited by vincent09: Jul 30 2007, 09:21 AM

Thank you Doom and mADmAN for the suggestion.
The ATX cable look like hard to fold, look like imposible to fold for me

Ok i try my best think of it to get nice management.